Page 1 of 1
JIMNY BUILDUP
Posted: Sun Oct 30, 2005 8:41 am
by OVERKILL ENG
We have just finished a Jimny Buildup here are the buildup pics.
Someone posted a link to the workshop page before but it got moved because it wasn't tech i thought buildup pics were tech.
http://www.overkill4x4.com/Jimny.html
SAM
Posted: Sun Oct 30, 2005 8:53 am
by Bad JuJu
Thats cool
Posted: Sun Oct 30, 2005 9:17 am
by hypo
Posted: Sun Oct 30, 2005 10:09 am
by Bad JuJu
One question, why did you weld the sliders direct to the chasis instead of to an intermediate plate that could spread the load to the chasis over a wider area ??
I can only see the middle mount, the others may be different I realise.
Posted: Sun Oct 30, 2005 10:13 am
by redzook
Bad JuJu wrote:One question, why did you weld the sliders direct to the chasis instead of to an intermediate plate that could spread the load to the chasis over a wider area ??
I can only see the middle mount, the others may be different I realise.
do u reckon its goin some where?
attaches 3 places then tied to the exo
its goin no where
Posted: Sun Oct 30, 2005 10:28 am
by WHITS
sweet looking rig...........nice job boys
Posted: Sun Oct 30, 2005 6:45 pm
by Bad JuJu
redzook wrote:Bad JuJu wrote:One question, why did you weld the sliders direct to the chasis instead of to an intermediate plate that could spread the load to the chasis over a wider area ??
I can only see the middle mount, the others may be different I realise.
do u reckon its goin some where?
attaches 3 places then tied to the exo
its goin no where
Did you build it ?, if so can you answer the question please... if not and you can't attempt to be polite, well .....
Posted: Sun Oct 30, 2005 7:05 pm
by redzook
Bad JuJu wrote:redzook wrote:Bad JuJu wrote:One question, why did you weld the sliders direct to the chasis instead of to an intermediate plate that could spread the load to the chasis over a wider area ??
I can only see the middle mount, the others may be different I realise.
do u reckon its goin some where?
attaches 3 places then tied to the exo
its goin no where
Did you build it ?, if so can you answer the question please... if not and you can't attempt to be polite, well .....
no i didnt build it (I dont work for overkill)
how wasnt i being polite?
u may have just read it like i wasnt being polite
hard to tell with the internet
Posted: Mon Oct 31, 2005 7:03 pm
by OVERKILL ENG
Bad JuJu wrote:One question, why did you weld the sliders direct to the chasis instead of to an intermediate plate that could spread the load to the chasis over a wider area ??
I can only see the middle mount, the others may be different I realise.
The middle mount is straight onto the chassis the front mount goes onto the body mount as well as the chassis and if you look real close you can just see that the rear mount actually goes into the factory crossmember and through the chassis rail
SAM
Posted: Mon Oct 31, 2005 8:36 pm
by Bad JuJu
Thanks Sam.
Its pretty damn cool.
The numbers of un rolled, un chopped & un rusted Sierras must run out one day.
Its good to see development of the next gen of factory solid axle zooks..
Posted: Mon Oct 31, 2005 8:49 pm
by antt
lookin good sam. that x90 is wild
Posted: Mon Oct 31, 2005 10:33 pm
by Zute
Whats the tyre size?
