Page 1 of 1
mating D20 T/case to TF 727 transmission ?
Posted: Thu Nov 10, 2005 6:09 pm
by Xtremitys
Howdy,
i recently bought a 68' J200 4x4 as a project vehicle , it has a 232 , 4 speed box & a Dana 20 case.
I am using the driveline from a 82' cherokee ( AMC 360 , TF 727 ) that i had , alot of people retain the D20 case which i want to keep in there . Have a 208 - but the output to the front axle is on the different side & doesn't match the frontend ,(unless a 241OR Rock-trak comes along )
I want to mate it up to the torque flite - does anyone have or know of the conversion part/kit that mates the two ???
Any help would be greatly appreciated
cheers
Rick
Re: mating D20 T/case to TF 727 transmission ?
Posted: Fri Nov 11, 2005 11:02 am
by scout392
Xtremitys wrote:Howdy,
i recently bought a 68' J200 4x4 as a project vehicle , it has a 232 , 4 speed box & a Dana 20 case.
I am using the driveline from a 82' cherokee ( AMC 360 , TF 727 ) that i had , alot of people retain the D20 case which i want to keep in there . Have a 208 - but the output to the front axle is on the different side & doesn't match the frontend ,(unless a 241OR Rock-trak comes along )
I want to mate it up to the torque flite - does anyone have or know of the conversion part/kit that mates the two ???
Any help would be greatly appreciated
cheers
Rick
Iam i bit confused you have a D20 on the back of a T18 spd and a 208 on the back of a tf7727.
Yay or nay
Eric
Posted: Fri Nov 11, 2005 4:35 pm
by Xtremitys
- NP 208 is out of the cherokee ( AMC 360 > TF 727 > NP208 ) that i have , wrecked the cherokee for parts .
- dana 20 is in the J seies ( AMC 232 > T18 > D20 ) is my current project , plan to take out the 232 & T18 and replace them with the AMC 360 & TF 727 , leaving the D20 there !
conversion kits
Posted: Mon Nov 14, 2005 10:46 am
by 74cj6
its a shame you dont have the cherokee driveline that has a th400 as i have an adaptor for the th400 to the d20 case. i do know that marks does adaptor kits for these combos but they are in the old advance adaptors range so it takes some searching..
other than that u could pickup a th400 amc pattern box and buy my adaptor if it suited
goodluck mate
Posted: Mon Nov 14, 2005 2:13 pm
by scout392
Xtremitys wrote:- NP 208 is out of the cherokee ( AMC 360 > TF 727 > NP208 ) that i have , wrecked the cherokee for parts .
- dana 20 is in the J seies ( AMC 232 > T18 > D20 ) is my current project , plan to take out the 232 & T18 and replace them with the AMC 360 & TF 727 , leaving the D20 there !
You may need to get a tail housing from a TF727 inc bull gear.
Eric
Posted: Sun Jan 08, 2006 9:46 pm
by Xtremitys
sold 727 & NP 208 , now committed at going manual ( T18 which i have & splitter ) and strong possibilitydropping the 360 in favour for a AMC 401 !
Posted: Mon Jan 16, 2006 2:29 pm
by scout392
Xtremitys wrote:sold 727 & NP 208 , now committed at going manual ( T18 which i have & splitter ) and strong possibilitydropping the 360 in favour for a AMC 401 !
Good choice have heard a lot of good thing about the 401.