Outer Limits 4x4 Board

i need say 3" pipe no bends.. i need say 2 meters......

if anyone nows a plane in melbourne.....

thanks

peter

got mine from tubesales in tomastown.

sorry can't rember the price tho.

x2

thanks buddy...... ill give them a try tomorrow....

cheerz

peter

Charged_ZooK wrote:i need say 3" pipe no bends.. i need say 2 meters......

if anyone nows a plane in melbourne.....

thanks

peter

Tube sales in Temple drive Thomastown, They should have stainless mandel bends as well.

Very freindly service. Mate deals with them a lot.

Shane

cheap as...... for 3" tube no bends at $22 a meter.!!!

my concern is one of my mate on his patrol has this set up but he has joint the stainless steel with 90 degree and 45 degree black rubber bends.... i dont no were to get these.. i have tried reece plumbing altho they dont no what i talk about...... i dont want manderal bends due to i dont partuicually like seeing the welds!!!!!

HELP ME

Charged_ZooK wrote:cheap as...... for 3" tube no bends at $22 a meter.!!!

my concern is one of my mate on his patrol has this set up but he has joint the stainless steel with 90 degree and 45 degree black rubber bends.... i dont no were to get these.. i have tried reece plumbing altho they dont no what i talk about...... i dont want manderal bends due to i dont partuicually like seeing the welds!!!!!

HELP ME

why would you see the welds if you manderal bend something?

grimbo wrote:

Charged_ZooK wrote:cheap as...... for 3" tube no bends at $22 a meter.!!!

my concern is one of my mate on his patrol has this set up but he has joint the stainless steel with 90 degree and 45 degree black rubber bends.... i dont no were to get these.. i have tried reece plumbing altho they dont no what i talk about...... i dont want manderal bends due to i dont partuicually like seeing the welds!!!!!

HELP ME

why would you see the welds if you manderal bend something?

I think he's referring to the bends that you buy and then weld in between sections of straight pipe.

Anyway I reckon the black rubber bends look better than steel bends, just personally, as well as being more DIY-friendly.

the black rubber bends should be able to be located at any truck spares place. im from sunny qld and the pipe is the same price up here, thats good to know...



cheers
PAUL

yeah i want the bends.... does anyone no where to get them from.....?????

what do i ask for aswell....?? wat they called????

i am a little simple... only as student.........

There's a massive truck spares joint on sth gippy hwy dandenong. I might drop in and check it out. As for what they're called or used for i don't know...yet.

they may even have 'em in 4"

GQ Bear wrote:There's a massive truck spares joint on sth gippy hwy dandenong. I might drop in and check it out. As for what they're called or used for i don't know...yet.

they may even have 'em in 4"

thanks for that GQ Bear

yurp, called truck spares i think, just premoulded rubber bends for intakes. cost me around 90 bucks i think for two 45's and a 90. when u cut the hole in the guard, go to clark rubber and get a rubber strip with a groove cut down it, cut it so it covers up the cut, i can get a pic if need be???

vanbox wrote:the black rubber bends should be able to be located at any truck spares place. im from sunny qld and the pipe is the same price up here, thats good to know...



cheers
PAUL

Hey mate, where bouts did you get your quote from?

cheers,

Luke

^ Same question here Paul
thanks :)

thanks for that fellaz..... i will be sure to give that truck place a bell.....


they look way better than say a safari snorkal.... and besides the fact you can replace insted of buying a new one if gets tiped on....

can you post up that pic big bundy......????.

thanks

Truck bits in dandenong/bayswater

90^ bend 3" - $19.80
45^ bend 3" - $26.50
Donaldson Ram head (safari style) 3" inlet - $36

those prices were as of bout 6 weeks ago when i was pricing

you also have to buy the pipe clamps for the rubber bends which were about $4 each...

fnukle wrote:^ Same question here Paul
thanks

X3
and what did you use to stick yours to the vehicle with

Truck bits in dandenong/bayswater

90^ bend 3" - $19.80
45^ bend 3" - $26.50
Donaldson Ram head (safari style) 3" inlet - $36

those prices were as of bout 6 weeks ago when i was pricing

you also have to buy the pipe clamps for the rubber bends which were about $4 each...

yeah its not that expensive
http://www.4wdmonthly.com.au/forum/inde ... adid=16416

i made mine the same way but used some black plastic tube from bunnings

I did the same with mine


Got them from Robertson Brothers Truck Spares here in Newy... They are the local Donaldson dealer.

The 45 deg was $28 and the 90deg was $19... go figure.. lol

yea thats the shit dude thats look great.... where is this place in melb for the truck spairs.....????

There's a massive truck spares joint on sth gippy hwy dandenong
round here somewhere!!!!

yea i have found it on whereis.com.au and i found it... its only around 30 mins from mine......... i might give them a call....

hey turbo GQ are you wanting some bends........????

i will be getting 2.. 45s and 1.. 90 degrees.... in 3"

make it thursday ill come with ya.

HEHEHE
YEAH HEHEHE
IM FUNNY ANT I