Page 1 of 1
80 series body lift - HELP - Update
Posted: Sun Sep 24, 2006 8:55 pm
by g35me
just started a body lift tonight on my 80. And damnit I'm stuck on the first set of bolts next to the radiator. When you remove the nuts from the body mounts underneith arent the bolts then meant to slide out from the top? I have bashed the crap out of them from undreneith and they are not moving up. What is going on? Thanks
Posted: Sun Sep 24, 2006 10:00 pm
by RV80
The bolts will be rusted and seized in. I had the same problem, jack the body up a bit to help dislodge them and spray in heaps of wd 40....
Posted: Sun Sep 24, 2006 10:02 pm
by g35me
just sprayed then with wd40...you think I can jack the bolts up?
Posted: Mon Sep 25, 2006 12:13 am
by Bluey
if you can't move em by bashing, i would try the jack. BUT be very careful that whole doesn't down on someone blah blah i'm sure you know this
Posted: Mon Sep 25, 2006 12:23 am
by g35me
I was in Hobart yesturday
Posted: Mon Sep 25, 2006 7:59 am
by dow50r
Brian
The front mounts have a single bolt through the midle, and two small threadded bolts on the outside to attatch the mount to the Radiator support...you need to undo the centre one to lift the body, leave the other bolts done up to the RSP...
Andrew
Posted: Mon Sep 25, 2006 11:56 am
by Bluey
brian haines wrote:I was in Hobart yesturday
and it was perfect weather too
showers one minute, rain the next
Posted: Mon Sep 25, 2006 1:28 pm
by g35me
It was perfect all week then when I turn up on Thursday it turned bad. Just my luck.
Posted: Mon Sep 25, 2006 9:15 pm
by g35me
So this is where I am at tonight. I put the jack under the front bolt next to the radiator and then jumped up and down on the bullbar about 50 times and it finally come free.
I then removed the one near the pedals with out to much problem then the one just behind the drivers seat spins top and bottom but the nuts wont come loose. Unfortunately I have now rounded the bolt and tomorrow night I will attenpt to gring the nuts off which hopefully I can just slide the bolt out. We will see.
Posted: Mon Sep 25, 2006 9:58 pm
by Bluey
Brian, you sure are having trouble getting the bolts outs
what engine and gearbox do you have, think there is less work on a auto than a manual. still tossing up whether to do mine
Posted: Tue Sep 26, 2006 5:38 pm
by g35me
Its a 3FE auto. I picked up my Marks Adapters kit today and I get my 350 chev next week (It is still being built). So in about 3 weeks it will be a chev V8.
Posted: Tue Sep 26, 2006 10:16 pm
by g35me
OK...have cut off the bolt in the centre under the drivers seat. Made a mess of the body mount bracket but I will worry about that later. Removed the bolt under the rear seats, got the wife to use the rachet while I was underneith looking up her skirt
How has everyone bolted the rear mount on. I cant fit the extended bolt through the gap in the body. Do you put the bolt in upside down and the nut is done up in the body cavity?
Posted: Wed Sep 27, 2006 5:03 pm
by RV80
I put the rear bolts in mine upside down, i know people have drilled holes up top to drop them in but i dont see the point in that... It makes no difference if they're in the wrong way...
Posted: Wed Sep 27, 2006 5:59 pm
by g35me
yep, upside down it is.