Page 1 of 1
Transfer case gears
Posted: Tue Nov 14, 2006 6:59 pm
by 410sierra
I'm looking at getting some reduction gears for my transfer case
but my problem is I have a 1984 1 litre case with a 4wd light switch
and cant find any gears to suit it.
Does anyone know of any?
Would 1.3 litre reduction gears fit into mine?
Thanks Brad
Posted: Tue Nov 14, 2006 7:20 pm
by muppet_man67
mate I don't think you will find it hard to find someone on here to do a swap with you.
Posted: Tue Nov 14, 2006 7:23 pm
by Potter
hi brad ill swap.
Posted: Tue Nov 14, 2006 7:27 pm
by 410sierra
excuse me for not being quite with it but whichbit do you
want to swap?

Posted: Tue Nov 14, 2006 7:28 pm
by ofr57
i know that you cant fit 1.3 gears to a 1 litre
I would ask christover1
http://carl.outerlimits4x4.com/profile. ... file&u=374
i think his is a 1 litre
Posted: Tue Nov 14, 2006 7:28 pm
by Potter
does you tcase have gears in it?
Posted: Tue Nov 14, 2006 7:29 pm
by 410sierra
yeah it has gears in it
Posted: Tue Nov 14, 2006 7:33 pm
by Potter
i have a 1.3l tcase that ill swap
Posted: Tue Nov 14, 2006 7:34 pm
by 410sierra
will it bolt straight in or will it need modifacation?
Posted: Tue Nov 14, 2006 7:35 pm
by Potter
im not sure, one of the other gurus will have to answer that question.
Re: Transfer case gears
Posted: Tue Nov 14, 2006 10:40 pm
by Podge
410sierra wrote:I'm looking at getting some reduction gears for my transfer case
but my problem is I have a 1984 1 litre case with a 4wd light switch
and cant find any gears to suit it.
Does anyone know of any?
Would 1.3 litre reduction gears fit into mine?
Thanks Brad
On the information that you have provided any low range gear set will fit, even standard 1.3 gears will fit (though they would be a higher ratio).
Posted: Tue Nov 14, 2006 10:59 pm
by muppet_man67
why are the casings the same? why are they never advertised to fit 1l cases as well?
Posted: Wed Nov 15, 2006 3:59 pm
by Nev
yeh im pretty certain 1L cases with the switch are the same casing as the 1.3L just different internals and flanges.
Posted: Wed Nov 15, 2006 5:23 pm
by 410sierra
I just got an email back from Rocky Road Outfitters and this is what they said
"The gears will fit in your transfer case. However, your tcase is 12% lower than the regular Samurai tcase. So you would just take both the high and low range numbers and reduce them by 12% to get your final gear change."
so i take it that they will fit

. I just didnt want to spend the money and find they dont fit
Posted: Wed Nov 15, 2006 8:37 pm
by Nev
that sounds spot on to me....percentage change in gearing will be less in a 1L case but hey.....still the same low range gearing in the end. Can I make one point though. 1L cases with the switch are reasonably sought after compared to 1.3's. I was in the exact same position as you as I had been using a 1L case before I bought my gears and I sold my 1L case for $250 and you can pick up 1.3L cases for about $50. I would think about this if you arent likely to swap back in the near future or havent just rebuilt the case. Can understand its a bit of fiddling around though for a couple of hundred $$ but just thought id mention it.
John
Posted: Wed Nov 15, 2006 8:44 pm
by 410sierra
yeah i just decided to get a set of series 1 rockhoppers for the 1 litre
it worked out about 400 bucks cheap for the same gear reduction
Thanks for every one help Brad