Outer Limits 4x4 Board

GDAY
i have a suzuki sierra 91 model
i am in the hunt for race seats/bucket seats to fit, there is shit all room in the cab, i am worried to buy seats and they will not fit...
any advice/ideas would be great.

Dan!

Mine fitted just fine, and so have many others I've seen. I don't think you'll have too many dramas.

hi mate,

what are the sizes width and stuff

hi markil did you get them seats off ebay? i got a set the same and i tell ya they are no good for off road becouse i found out the hard way a bar in the bottom that goes across your lower back is the problem got some air came down could not drive for the rest of the day pain train for me they would do good in a car that not going to go off road any way

Daniel wrote:hi mate,

what are the sizes width and stuff

They are about 500mm wide.

zookpower1 wrote:hi markil did you get them seats off ebay? i got a set the same and i tell ya they are no good for off road becouse i found out the hard way a bar in the bottom that goes across your lower back is the problem got some air came down could not drive for the rest of the day pain train for me they would do good in a car that not going to go off road any way

I got them as a Bday pressie off ebay I think yeah. I've had mine in since april and love em. I've put a bit more padding in mine too They take a bit to get used to, but they sure keep you in your place when needed On long trips onroad I don't like them as they are non reclinable though.

I have one of these seats off Ebay. They are basically a Monza rip off but they are narrower and so more suited to Zuk's (and narrow arses). Once you get used to getting in and out of them they are pretty damn good. You don't move around at all once your in it. The seat rails are 5mm wider then the stock rails and after stuffing about trying to make Zuk rails fit seat, I just drilled holes in the body brackets and used high tensile bolts and large washers. Sturdy as, and no doubt a rolling defect but it works.

WTF? You start another thread Daniel?

http://www.outerlimits4x4.com/viewtopic ... port+seats

=SKB= wrote:I have one of these seats off Ebay. They are basically a Monza rip off but they are narrower and so more suited to Zuk's (and narrow arses). Once you get used to getting in and out of them they are pretty damn good. You don't move around at all once your in it. The seat rails are 5mm wider then the stock rails and after stuffing about trying to make Zuk rails fit seat, I just drilled holes in the body brackets and used high tensile bolts and large washers. Sturdy as, and no doubt a rolling defect but it works.

I have hyundi exel seats in mine! And like =SKB= they are just boled with square steel tube to get the height right! One of the most illegal mods you can do but like he said it woks a treat!

that post was few weeks agi, it was difftoo. i wanna know what people use and what sizes...
sorry am i only aloud 1 post of the same thing? lol

leave me alone i like to be ensured

Dan!

that made no sense sorry..
i just want to know what size seats people are using.
just like to get a few more responses!
Dan!

Got a set of SAAS recliners in mine, the shoulders are tight to the targa bar, but otherwise neat fit.

Fitted using stock rails, redrilled rails and floor pan, used stainless 50mm angle on drivers rear to allow the rails to move in.

All engineered and legal.

Spock

btw some pics at website... early article or maybe in reviews..

ONCE THE SEATS ARE IN.. HOW DO I GET IT LEGAL?
IF THE SEATS ARE ADR APPROVED DO I STILL NEEED ENGENEER?
IF NOT WHAT DO I HAVE TO DO!!

DAN!!

Ask your local regulator,

up here i still needed a engineer coz the rails moved.

Spock

Daniel wrote:ONCE THE SEATS ARE IN.. HOW DO I GET IT LEGAL?
IF THE SEATS ARE ADR APPROVED DO I STILL NEEED ENGENEER?
IF NOT WHAT DO I HAVE TO DO!!

DAN!!

I think as lond as they are secured to your old seat mounts or slidey thing they alright but it's when you rip all that out and put other stuff in that it gets ugly!

thanks,
i bought some saas seats that will definetly fit onto the old rails.
i dont know if the seats are ADR approved, but i think they would be..

Dan!

in queensland at least they must be adr compliant and any change of seat must be mod plated. If you change seat mounting system etc. I presume an engineer must be involved if its even legal.