Outer Limits 4x4 Board

DOES ANYBODY KNOW WHERE I CAN BUY COMPLETE BOLT IN TURBO KIT FOR TB42 PETROL ONLY NO GAS ,ANY HELP WOULD BE GREAT THANKS DARREN

ontrack4x4

jpc

Did you contact Paul @ CVE Performance?

hottiemonster wrote:jpc

HM your alive havent seen or heard from you in ages.
So is the Shorty getting a JPC system?

if you can come down vic to get a turbo done. Go to ontrack, aus4wd, or JPC. All know there shit and race. So they know whats going on.

Go to aus4wd as ontrack are very expensive.

where ever u take it, quality counts........ thats why ON TRACK got the job of building my new motor.
Old motor by JPC only did 30,000k's
think twice, act once.

TURBO GQ wrote:where ever u take it, quality counts........ thats why ON TRACK got the job of building my new motor.
Old motor by JPC only did 30,000k's
think twice, act once.

got the specs?

"where ever u take it, quality counts"

Yes and i have no doubt that they are top quality but from personal experience i have been quoted massive amounts from them on certain turbo work (topic of this forum). I would be going back to whoever built your motor that only lasted 30,00km. I think motor rebuilds should be left to engine "specialists" rather than 4wd shops.

I did a lot of shopping around and aus4wd did a great job on a manifold at well under half the cost of ontrack. If i didnt go there i would have been at CVE performance. "Mulisha" from this forum has got one of their kits and it looks top quality.

Jimmy

jpc do alot more diesel work than ontrack ontrack are still one of the best but i would go jpc for any diesel truck

Has anyone got contact details for all the above? im also interested in this set-up.
Thread jacking over

Steve.

Sandy Bowman
Aus4wd (not sure if thats the real name....along those lines)

97294899

http://www.ontrack4x4.net.au/

And I have seen some of the diesel work that Juzza does. You could also PM him. Turbo and intercooler systems for diesel and petrol.......PM Juzza. Thats what his sig says.
Seen a GU with his setup and it goes well.

Thanks fellas, has anyone got the number for JPC?


Time for some research me thinks

Steve.

Thanks fellas, has anyone got the number for JPC?


Time for some research me thinks

Steve.

Talk to all of them, then talk to people that they've done work for.

AUS4WD is 03 9729 4899

OnTrack4x4 is 03 9331 6536

JPC is 03 9469 2566

turps wrote:

hottiemonster wrote:jpc

HM your alive havent seen or heard from you in ages.
So is the Shorty getting a JPC system?

yeah Carl, i have been dead lately, so much going on.

Car will not be getting a JPC system, but another type of system which has been completed already, boostin' to about 15 atm.

go onto jpc's website and check out all there work www.jpc.com.au and talk to mark

do tell hottie.....

as like so many 4wd shops ,the price has gone through the roof and way beyond most of us ....oh well they'll come back to earth once things die down...

"as like so many 4wd shops ,the price has gone through the roof and way beyond most of us ....oh well they'll come back to earth once things die down..."

I agree but i got a manifold made up by AUS4wd and they were very cheap considering how good the end product is and how much everyone else wanted. I also found that going through non-4wd shops was a lot cheaper. Manifolds made up from shops that only do that kind of stuff were pretty cheap, the only reason i went to aus4wd was because they didnt need my gq in there to jig it up!

viperguy wrote:do tell hottie.....

i am not 100% sure about what setup i am running, i bought the setup off a member of a 4wd club i am in. I am only new to it