Outer Limits 4x4 Board

Thanks for that, not sure if i will have more luck finding patrol rims than paj ones as i bet they are pretty popular, but i guess there would be a few around too.

Have done a bit of a search and have come to the conclusion that patrol rims may fit ok but not sure what year model, and maybe navara/4 runner rims? looking for a second set of 16 or 17 inch rims with standard tyre's when im not using it offroad. Have thought about using nm/np/ns rims but have ...

Thanks for the reply's, will probally go with a second set of rims and some smaller tread for the time being and see how that goes... much cheaper and easier option if it works out.

Sorry for the late reply Ian, have been away, just sent you a pm and now reading your post.. great to hear you got it sorted!

Hi all, After recently needing to swap a 2.8 Td V5M31 5 speed manual into my paj i have noticed that in comparisson to my petrol box it has a much taller 5th gear, from my searching all other ratio's are the same. Been doing alot of towing lately so considering fitting some 4.90 diff ratio's to ...

Hi Ian, not sure if you have found the problem or not but my paj did a similar thing before i stuck a diesel in it, If it run's fine at full throttle and above 3,500 rpm and hesitates below this than i would suspect its the o2 sensor. Its at about this point/throttle setting where the computer ...

Hi Ian, The 3.2 is going great, no problems at all so far, put over 10k on it already with a couple of trips to the high country and coffs coast. No regrets with doing the changeover from the s/c v6 to the Did, only let down i have found so far is probaly on the freeway/overtaking, where the petrol ...

My shorty NL paj has a 3.2 Did in it with a 2.5 inch mandrel bent system and hi flow muffler, not sure if its makes a difference as i had to mod the exhaust as part of the conversion.

Anyone know if the cat is a requirement on diesels these days?

Cheers, ben

How would you guys with the bigger reduction transfer gears rate them off road? Worth the money and the trouble of putting them in?

Can definately get o2 sensors aftermarket, about $150 compared to $600 genuinie. have the part number at home for the NGK one if you need it, got mine from repco. Not sure about the ISC motors but, you are talking about the idle stepper motor i guess? I have one for the 6G74 SOHC motor at home if ...

Sounds good frank, hope it all works out and i can finally twin lock my paj

Let us know when you hear more.

Ive got one of a 99 NL pajero that i can sell you, not sure if there the same but would be worth the inquirery.
Have they tested the thing properly and plugged in their diagnosis equipment? Haven't heard of many of these failing on the later engines.

Yeah i got an after market weep to, get your's from repco or super cheap?

Scott, might pass on the swap this time, although yours is a nice rig, maybe you should trade yours on a new one when they come out then we can swap

damn i got a C.V joint, must be a NL shorty thing?

Yeah not talking about the front prop shaft, what i was saying in the last post is i have a C.V joint at the front of my tail shaft, (where it slips into the back of the gearbox). There is a uni joint at the back of the tail shaft where it bolts up to the rear diff flange. So is this the same setup ...

Thanks for the replys, will check out the welsh plug and let you know. So when the welsh plug leaks does the oil apear to be comming out around the C.V joint area (my tail shaft has a C.V joint at the front not a uni joint), not sure if you guy's have the same? The oil seams to be spread out pretty ...

Have made a couple of attempts to fix this damn oil leak in the last couple of months and no success. Before i pulled the box out to put the diesel in, the front output shaft seal was leaking and the rear was fine. replaced all the seals when the box was out, now the front is fine and the rear ...

Very nice, good to see mitsubishi seem to be listening to the public and bringing the MIVEC petrol into the range that they have had available for years in japan.... and the shorty again

If your gonna be towing a bit, i would reccomend the 2.8 turbo diesel over the petrol. People say that the diesel's are a bit more expensive to maintain, but if you can do oil/filter and fuel filter changes yourself, the difference is pretty minimal. Go for the NH/NJ onwards if you can afford it ...

Yeah just a rattly old 'Did' haha

Ben

Count me in, hope they go through with it

Cheer's, Ben

How about a 6G74 SOHC 3.5 litre from a 99 NL pajero. Have one for sale with all the bits you will need to put it in if your interested.
Pm me if you are,

Cheer's, Ben

Why not put a 3.5V6 SOHC 6G74 out of a NL 99 model pajero in it? I happen to have one for sale with loom, ECU, mounts, starter, alternator, bellhousing, airbox + spares with 125,000 on it. :) Just done the water pump, timing belt, all seals etc at 90,000. Asking $2500, better motor than the 6G72 ...

Finally, have been waiting for one to come out for ages

Cheer's, Ben

Something to do with their Dakar winning history i suppose, fully adjustable suspension, awesome brakes, MIVEC engine, and definately the aggressive looks

Those things are awesome, tried for ages about 5 years ago to import one before i bought my NL SWB in Aus, back then the restrictions on low volume imports made it impossible to register them for road use but now things have changed... i just want one :) If only i could afford to keep mine for ...

Interesting thought Ian, not sure it would be a step in the right direction though going back from efi, but would definately give you a big boost in torque with the V8. I thought of a few options before i started on my supercharger conversion, one of them was getting my 3.5 motor rebuilt to the same ...

As far as i can tell via the website, the gregory's/haynes manuals only go up to 96 NJ model. Need one for NL 97 and up with the SOHC motor, 5 speed manual.

Hi all,

Just wondering if anyone out there has a wiring diagram for the NL 97-99 pajero, 3.5V6 SOHC 5 speed manual. Or does anyone know the best place to get one?

Cheer's, Ben

Still for sale if anyone is interested, had a couple of people interested but have pulled out, so PM me or email me at benl227@hotmail.com if your keen,

Cheer's, Ben