Outer Limits 4x4 Board

I have a 3Y gen 1 runner also..
I have trouble getting to 120km/h with only a bit of gear in it running 31's :bad-words:
Doubt the old girl would top 100 with 35's, especially with the speedo discrepancy!!
I've nearly finished the "gathering parts" stage of a 7M-GE conversion :armsup:
7M-GE ...

Go 30's and never worry about cv's again

dang those are some bad pics!
should be a nice truck though

I run a pump off my engine using a electric clutch with a timing belt off the crank with an auto. I believe its better because with a PTO if you throw the clutch you lose drive and winch. Mine is a warn 9000lb industrial with a different pump and set at 2750psi and it pulls at 152 feet per minute ...

surf diff converted to full floater, dual triangulated four link, coil dropouts, Pathfinder/Terrano 40mm lift OME coils (#OME920) Aceytl spherical ball joint to guide coil dropout rod.
http://i77.photobucket.com/albums/j61/Jafa_NZ/Hilux/perchunder2.jpg

http://i77.photobucket.com/albums/j61/Jafa ...

Guts wrote:

Roctoy Designfab wrote: They are by far the coolest looking hilux trays!

If you think so.

And sucky rear shackle angle too

Yeah saw that, thanks!
lemme know when ya want your pair of arms and I'll do ya deal

:D okay no more bee tee tees

;)

No worries. If you want to advertise them you know where to do it. Im happy for this to stay here for others future reference. It is a product that i do beleive is needed. And i cant see Trailgear making it the near future. Although with the amount of gear that ...

okay no more bee tee tees

btt

WICKED wrote:Does that price inc. the Marin 6 shooter knuckle?

nope, arms only

Here they are at last!
Billet steel, one piece 6 stud HiSteer arms for us RH drivers. These are designed to fit the Trail-Gear 6 Shooter knuckles for the ultimate steering solution for your Hilux. These arms have the kingpin as part of the arm itself, they are CNC machined from a block of P20 steel ...

We make a set as well, and tie rods, tie rod ends, draglinks, jam nuts IFS pitman adapters etc

http://www.snr.net.nz

the turbo sump is a mid bowl as opposed to the NA which is front bowl, have a look here, lots of good info on the swap

http://board.marlincrawler.com/index.php?topic=11982.70

yer ya really need to find a Turbo 7m (7mgte) sump, oil pump, pickup and hardline and swap that in. You dont need to if you have normal shitty Hilux j-arm steering

Tapage wrote:

jafa wrote:W series boxes have the same bolt pattern as the G boxes...so yes it will fit, if its a g52 5 speed in your truck

The question it .. the G52 can handle the power ?

No worries, mine has no issue with the 7mge at all

W series boxes have the same bolt pattern as the G boxes...so yes it will fit, if its a g52 5 speed in your truck

Cant fit snow chains on the front wheels.....no wait, thats right, not a lot of snow in Qld...

have a look here

http://www.awshifting.com

Have you checked out Cebby's thread on Lextreme.com? He did a shaft swap in his

i dont think he swapped the shaft

I think he ended up adding the sensors and valvebody from a lexus trans to a 4runner/surf trans. i seen a few of his posts.

Jes

Ahh yes, I had a re-look at his stuff, he did an ...

Have you checked out Cebby's thread on Lextreme.com? He did a shaft swap in his

You ncan use the auto belhousing, which is pretty common, and an adapter plate.

Check this build out, goes really well too apparently


http://www.offroadexpress.co.nz/modules ... pic&t=2633

i should know this, but i dont.

do these arms only fit lux or some cruiser also, i need arms for my 40 and i think i remember being told the stud pattern is different.

Mate they do fit the cruisers 60-40s but you need to remember that the arms come with an 80 series taper for the tie rod ends ...

This company in Italy makes a PTO unit thats bolts to the side of the hilux transfers with the pto port

http://www.omfb.it/web_eng/catalogo/scheda_prod_leg.asp?id=06700500139&f=134&r=16&l=174&lingua=ENG

good luck getting one, there might be an agent in Aussie tho , none in NZ, so I didnt go any ...

one in NZ, single turbo

Hey Fella,
I'm in the middle of doing a 1UZ and I have already done a 7mge swap on my daily driver Surf. The 1Uz is 5k all up I guess, and the 7m was about 2500 all finished, heres a link to my 7m swap. Bear in mind I could have used some cheaper and second hand bits, but In wasn't particularly ...

We are in production finally :lol:
NZ made Billet steel Toyota Hi Steer arms for $550 NZD per pair
http://www.atsl.co.nz/information.php?info_id=6

A few pics of the arms in production

http://www.offroadexpress.co.nz/images/albums/histeer/b4_bead_blast.sized.jpg

http://www.offroadexpress.co ...

*jz autos as well, good point, anyone know whats differnt between them and lexus A341? Hopefully just the tailhousing which I throw away anyway, mebbe different output shaft. As for price, still in the middle of costing it all up

Ok got some pics of the Lexus adapter design, those who are interested, let me know what yoy think of the design. It will bolt directly to the back of the Lexus A341, you will need to cut the thread of the output shaft of the trans.
It will have a double row bearing that the spline coupler runs in ...