Outer Limits 4x4 Board

save you the effort

http://www.candlepowerforums.com/vb/

http://www.kaidomain.com/WEBUI/ProductD ... ranID=2982

these drivers are great. and can run LED's in series.

remember that Luxeons [or Seuols or Cree's] need to have a heatsink on them or they will burnout.

check out candlepowerforums.com for more LED related info.

G

try this mob, i have used them a few times. based in hongkong, prices in US$ but includes postage. takes 2 weeks approx.

i have some LED replacement bulbs for the park lights on my 80series.

http://www.dealextreme.com/products.dx/category.907

god i hope not. :cry: i checked them out but its hard to tell even though they look the same. the wreckers have a set on a 90 model but they dont look like they are in that good a condition. i dont want an aftermarket set as i didnt want to spend big bucks before going away at easter and i want to ...

I have a 80series 1990 LC that has a saggy front LHS coil spring and i just want to do a changeover using a secondhand coil from the wreckers. i will be changing over the front 2 coils and was wondering what the difference between the 1990 model [series1] and the 1995 model [series 2] coils are and ...

years ago i put a set in a hilux, so much nicer than the stock bench seat. at first i just bolted them in, but found it too low, i ended up doing a 50mm spacer that i had bolted/welded between the rail and base plate and this made it perfect. about a year later i rolled it and wrote the car off ...

Pitto The wear starts in the c/v where the ball wears the outer, and on uphill corners, they start clicking. The c/v is 75% of the wear. The splines they run on also wear, and on early models, can get that bad, drive is lost, putting later (+8/92) drive plates and c/v's in stops it happening again ...

Thanks in advance for any assistance. i have been checking parts out on Ebay and have come across this kit. http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&ih=009&sspagename=STRK%3AMEWA%3AIT&viewitem=&item=190072417012&rd=1&rd=1 Does anyone know if this is a legit solution to fixing the slop in the ...

Thanks for the info, shall give em a call.

G

My cruiser was the first run of the 80 series. it has a mechanical speedo cable that runs off the side of the gearbox. the later models came out with the sender.

But what your saying is right, i will have to take note to see if the odometer stops when it has the next fit.

G

imagine say the inside of the speedo has plastic "gears" and due to the highspeed drill used to wind back the clock, they get damaged. then every once in a while they dont mesh and the speedo gos nuts whilst driving. i then have to pull over and the needle returns back to zero and then its fine ...

Hi All,

any recommendations on a diff repairer on the Gold Coast.

I replaced the oil the other week and it has now developed a nasty leak
around the pinion gear shaft.

Thanks for any info.

G

did our 80 series as well. It reduced the clunking which my wife says she can't hear.........funny hey, cause I think she can hear me talking about her from the other end of the house......so I'd better shut up. must be a "Lady Driver" thing [got to be PC and all ;) ] just need to convince her of ...

i was told this by an Auto Electrician, but there is a distinct cable [not wire} to the gearbox. The car is a 1990 gxl, one of the first run that came out with the 3f motor.

G

yep for sure... i did the part time on mine for this reason. i still had no manuel locking hubs on there but just the pt kit done in the t-case. it deleted the catch up thing that they do... (ps its even better when i fitted the manuel locking hubs.. Thanks mate, Thats what i was chasing. i tend to ...

Hi all, any recommendations on an external mounted fuel filter that would suit a petrol 3F motor??, pretty much like the racor one for deisel. The genuine Toyota ones a bit rich to replace all the time.

Thanks

G

Hi All, does anyone know of a place in brisbane/gold coast that does Speedo repairs. It turns out the previous owner of my cruiser thought it would be great to wind back the k's using an electric drill. so every now and then the speedo goes nuts and the needle goes off the clock. then rights itself ...

Hi all,

just a question, i have a 1990 80series gxl on lpg that has a bit of freeplay / backlash., would a Marks parttime kit solve this to a degree??

G