I need to replace my clutch and i'm looking at getting a a heavy duty clutch, a 4TERRAIN performance clutch by clutch industries! Has anyone had any experience with them? If not what type have you used?
Also at the auto parts place it lists two different types for my model 93 widetrack, two different splines? does any one know wich i would have or will i have to pull it out to check?
Cheers
Chop
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Heavy duty clutch!
Heavy duty clutch!
I THINK ICAN, I THINK I CAN!
The industry P/No. for a Sierra 1.3 w/G13A or G13BA is an R330N (Std) or R330NHD (H/D), Exedy P/No. SZK-6288 (Std) or SZK-6288HD (H/D). Some listings give a P/No. R335N but this is a Swift clutch kit. Use these P/No.s when ordering a 1.3 and you'll be right.
http://stores.shop.ebay.com.au/4wd-products
Once upon a time when I used to actually go 4wding and I had a Zuk I used a 4 puck sintered copper clutch pressure plate .. it was able to get hot as hell and just continued to hold perfectly ..
Make sure it has a sprung centre
Make sure it has a sprung centre
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
That looks like exactly what I had ... even after being oil contaminated it still worked (after it was boiled in soapy water for a bit to get rid of alot of the oil .. )CHOPS1 wrote:Well its been a while but i finally got one.
An extreme heavy duty button clutch. also had to get the fly wheel machined as it was stuffed.
Here's some pics as noone will be able to see the bling pink
chop
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
clutch plate
According to an old mechanic I know Sierra clutch can be replaced with VW Passat 2.0 not sure about pressure plate. Does anyone know a link to a clutch manufacturers specs catalogue? So I can check.
they're the new school button clutches i think, now using a normal clutch centre with buttons some run a solid friction plate on 1 side and button style on the other side.
the early button clutches were solid centred i reckon. about 8 years ago i remember a mate putting a button solid centred clutch in a spastic beetle, talk about launching off the line & brutal at the same time, quite difficult to drive normally but NO slip.
the early button clutches were solid centred i reckon. about 8 years ago i remember a mate putting a button solid centred clutch in a spastic beetle, talk about launching off the line & brutal at the same time, quite difficult to drive normally but NO slip.
Mine was sintered copper/ceramic was quite nice to drive with a lighter pressue plate (origionally installed with a centre force ... that was no good) The same puk types on both sides.atari4x4 wrote:they're the new school button clutches i think, now using a normal clutch centre with buttons some run a solid friction plate on 1 side and button style on the other side.
the early button clutches were solid centred i reckon. about 8 years ago i remember a mate putting a button solid centred clutch in a spastic beetle, talk about launching off the line & brutal at the same time, quite difficult to drive normally but NO slip.
It was reasonably progressive in the uptake and had a sprung centre.. even when the clutch was smoking it would still bit evey bite as well as when it was stone cold.
When I installed mine about 4 or 5 years ago it was custom made and cost heaps .. good to see that they are now stocked items, when I put the 1.6 in my new to me Zuk I will be installing one of these clutch's, the holding power compared to a stocker is fantastic ..
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Looks PURPLE to me....CHOPS1 wrote:Well its been a while but i finally got one.
An extreme heavy duty button clutch. also had to get the fly wheel machined as it was stuffed.
Here's some pics as noone will be able to see the bling pink
chop
but hey, as long as it works and is sweeet, who cares![quote="-Nemesis-"][quote="bj on roids"]whens the aussie one start?[/quote]
A few episodes before they can it? :lol:[/quote]
A few episodes before they can it? :lol:[/quote]
Who is online
Users browsing this forum: No registered users and 26 guests