Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

1HDT Oil

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Post Reply
Posts: 57
Joined: Sun Jun 18, 2006 9:13 am
Location: coffs harbour

1HDT Oil

Post by scotyz »

Whats the best possible oil i can run in my factory turbo 80 series for a longer big end bearing life . Its blown up once ,i would rather it didnt happen again. :x
Posts: 141
Joined: Fri Nov 12, 2004 4:46 pm
Location: Newcastle

Post by mickbeny »

Hi all...Caltex delo 400 CXJ.
PEACE...
Posts: 57
Joined: Sun Jun 18, 2006 9:13 am
Location: coffs harbour

Post by scotyz »

Is that mineral or synthetic
Posts: 6021
Joined: Sat Feb 15, 2003 11:01 pm
Location: Shed.

Post by dumbdunce »

delo 400 and delo CXJ are two different oils. you should use CXJ, the J is for Japanese, it has lots of calcium in it to help the dodgy factory big end bearings in toyotas. if, however, your engine was built with good aftermarket main and big end bearings (ACL are probably the best), then you can use any quality diesel oil.

Castrol Jmax is about the only other easily available oil that meets toyota's specifications for that engine, but I have had trouble with it thinning well before service interval, albeit with indirect injected motors, so it could be worth a try.

cheers

DD
Free air locker to the first 20 callers!
Posts: 1344
Joined: Thu Jan 12, 2006 10:12 am
Location: sydney

Post by sniper »

I use penrite
LANDCRUISER GXL 80series 4.2TD
[url=http://www.rag4x4.com]R.AG. 4X4 Club
RUFF~AS~GUTS[/url]
Posts: 211
Joined: Mon Aug 30, 2004 12:44 pm
Location: "the shire"

Post by quick60 »

dumbdunce wrote: it has lots of calcium in it to help the dodgy factory big end bearings in toyotas. if, however, your engine was built with good aftermarket main and big end bearings (ACL are probably the best), then you can use any quality diesel oil. DD
The calcium doesn't help the bearings, it's a cleaning agent and stops the build up of soot deposits in the gap between the top of piston and the top ring. Jap diesels have a tall thin gap, where US ones have a wide flat gap, so the engine needs to be kept clean here to avoid scuffing and bore wear. The bearing problem was a result of the wrong materials being used, not an oil issue.
Any oil with a calcium content of 3000 ppm or more will work best. My preference is ULX-110 Diesel supreme, which is a custom blend that will give you more protection than you need, and allow 20K change intervals.
Damian.

should I swim it first ?
Posts: 6021
Joined: Sat Feb 15, 2003 11:01 pm
Location: Shed.

Post by dumbdunce »

quick60 wrote:...The bearing problem was a result of the wrong materials being used, not an oil issue.
very, very reliable sources (who must unfortunately remain nameless) disagree. Craig Vincent has an excellent write up on it somewhere.

The 'wrong' material was (and still is) a part of toyota's alleged environmental initiative.

There are different flavours of calcium additives, perhaps they do both upper cleaning/bottom lubrication? I know zinc is the traditional contact/boundary lubricant for main/big end bearings, however the toyota bearing material is "different" (contains no lead for starters) and therefore needs different lubrication especially on direct injection engines to protect bearings especially at start and idle.

cheers

DD
Free air locker to the first 20 callers!
Post Reply

Who is online

Users browsing this forum: No registered users and 55 guests