Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Six point cage for 4 door

Tech Talk for Rover owners.

Moderator: Micka

Forum rules
Post Reply
Posts: 40
Joined: Mon Nov 08, 2004 3:46 pm

Six point cage for 4 door

Post by ratrangie »

Where have people got these from and how much will fit it myself .
regards Stu..
Top
Posts: 1175
Joined: Wed Jul 27, 2005 10:17 pm
Location: Mirboo North

Post by 6.5 rangie »

Most cages are built in the car and welded in, pretty sure you couldn't get a bolt in kit (diy). Try Browns Davis as i think their cages bolt together
Damien


--------------------------------------------------------
Top
Posts: 216
Joined: Sat Jan 15, 2005 9:29 pm
Location: Dandenong Ranges

Post by schuler »

Got to agree with 6.5 rangie, i had mide done at Malvern Motorsport, they were doing the cage for brockies FX Goodwood car at the time, check out the pics in "Post your rovers" Mark the fabricator is a genious, can't recommend them highly enough.

Steve
86 Rangie, F+R 4:11 Maxi, 35 Pedes, 6 point cage, Comp High Mount
Top
Posts: 3385
Joined: Fri Sep 17, 2004 8:26 pm
Location: Melbourne

Post by shakes »

mind giving a rough $$$ figure?
Top
Posts: 1175
Joined: Wed Jul 27, 2005 10:17 pm
Location: Mirboo North

Post by 6.5 rangie »

Around $2k, yours would be a bit less being a ute
Damien


--------------------------------------------------------
Top
Posts: 216
Joined: Sat Jan 15, 2005 9:29 pm
Location: Dandenong Ranges

Post by schuler »

Yeah, mine cost me around the 2K mark, etch primed but unpainted. we had a lot of discussion about design, to ensure the cage didn't impede access to the accelerator (can't have that) i was originally going to have a diagonal brace above the drivers head but issues with vic roads made me decide on a single brace in the middle of the vehicle. Malvern Motorsport do alot of historic touring cars and rally cars, however Mark used to work for ARB and has a good understanding of what we 4WD's need.

Steve
86 Rangie, F+R 4:11 Maxi, 35 Pedes, 6 point cage, Comp High Mount
Top
User avatar
Tiny
Road Ranger
Posts: 10722
Joined: Fri Nov 12, 2004 12:21 pm
Location: In a town near you

Contact:
Contact Tiny

Post by Tiny »

bond roll bars, fully bolt in units will freight anywhere at the right price, they make heaps of cages for supercars, rally and other race application and heaps to mines etc though out asia
If the above post did not offend you in any way please PM me so I can try harder!!
Top
Posts: 1057
Joined: Mon Feb 10, 2003 12:28 pm
Location: Eastern Sector

Post by mickrangie »

can i get a number for Malvern Motorsport......
TD5 96 Discovery UTE.
Top
Posts: 216
Joined: Sat Jan 15, 2005 9:29 pm
Location: Dandenong Ranges

Post by schuler »

mickrangie wrote:can i get a number for Malvern Motorsport......
Hi mickrangie,

You can contact them on 1300 72 66 54

Check out their web site

http://www.malvern-group.com.au/

Cheers

Steve
86 Rangie, F+R 4:11 Maxi, 35 Pedes, 6 point cage, Comp High Mount
Top
Post Reply

Return to “Rover”

Who is online

Users browsing this forum: No registered users and 0 guests