ive got a 94 sr5 with shitty ifs and those annoying auto lock hubs,
a mate of mine told me that if i was to fit manual locking hubs and disconnect the electrical to the solenoid on the front diff, the cvs would stay engaged in the diff, and all i would do 2 engage 4wd is lock hubs and push the button,
was just wondering about anyone else who has done this and is this right?
i'm guessing that the solenoid on the diff has 2 a normally closed one, but if it requires vacuum to hold it on, this isnt the way 2 do it
my number is 0421 22 1865. name is rob, would appreciate it if u knew anything about it if u could give us a quick buzz,
cheers[/code]
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
hilux, converting auto lock hubs to manual free wheeling
Moderators: toaddog, Elmo, DUDELUX
hilux, converting auto lock hubs to manual free wheeling
gq wagon, 5inch coils, 33 dick cepeks, rear locker, sliders, rear quarter chop, 4.2 turbo diesel high flowed and anneroid injector pump, 3inch exhaust,
give it arseholes!!!!!
give it arseholes!!!!!
Rob, you don't have auto locking hubs you have fixed hubs.
The 4Runner system is called ADD (automatic disconnecting differential).
The right axle is permanently locked to the wheel and the diff, whereas the left axle is only locked to the wheel. When you push the button, the ADD system locks the left axle to the diff via vacuum acutating a sliding splined collar etc and then you have 4wd.
It is common to remove these fixed hubs and fit freewheeling hubs as this allows the wheels to turn without also constantly turning the CV's, rubber boots etc. Its a straight bolt up and takes all of 10 minutes.
Unless you are expieriencing major issues with the actual vacuum actuation system just fit some hubs and leave it as is.
This gives you both scenarios. Whenever the hubs are locked you have normal ADD as it is now. With the hubs disengaged its not turning the axles, CV's etc when driving around town.
But be AWARE don't push the 4wd button while moving unless the hubs are locked first
The 4Runner system is called ADD (automatic disconnecting differential).
The right axle is permanently locked to the wheel and the diff, whereas the left axle is only locked to the wheel. When you push the button, the ADD system locks the left axle to the diff via vacuum acutating a sliding splined collar etc and then you have 4wd.
It is common to remove these fixed hubs and fit freewheeling hubs as this allows the wheels to turn without also constantly turning the CV's, rubber boots etc. Its a straight bolt up and takes all of 10 minutes.
Unless you are expieriencing major issues with the actual vacuum actuation system just fit some hubs and leave it as is.
This gives you both scenarios. Whenever the hubs are locked you have normal ADD as it is now. With the hubs disengaged its not turning the axles, CV's etc when driving around town.
But be AWARE don't push the 4wd button while moving unless the hubs are locked first
hubs
thanx ozrunner
that s what i meant, i know the cvs r disconnected from the diff,
but i am having issues with the solenoids under the bonnet i think, if i dont swap the hoses over, it will disengage after a short time, one solenoid mustn't open fully, and isnt allowing enough vacuum flow 2 hold the system on, i will fit the hubs anyway, my mate has got some,
thanx for your input
that s what i meant, i know the cvs r disconnected from the diff,
but i am having issues with the solenoids under the bonnet i think, if i dont swap the hoses over, it will disengage after a short time, one solenoid mustn't open fully, and isnt allowing enough vacuum flow 2 hold the system on, i will fit the hubs anyway, my mate has got some,
thanx for your input
gq wagon, 5inch coils, 33 dick cepeks, rear locker, sliders, rear quarter chop, 4.2 turbo diesel high flowed and anneroid injector pump, 3inch exhaust,
give it arseholes!!!!!
give it arseholes!!!!!
You can do one of 2 things....
1 - Buy a HILUX housing without ADD, strip your centre out and put it in the new housing. You'll need manual hubs and thats it. There are 2 wires to the FRONT of the diff, just bridge them and you trick the transfer allowing it to engage. The vaccum lines you can just loop in the engine bay and run a short piece to bridge them together.
2 - If you have solenoids playing up, i have 2 complete ADD housings that are in good nick with spare open centres for sale... both have been pulled apart and checked and everything looks great.
I've just taken route 1, and everything seems to be working fine. I haven't had it in the bush yet but testing it on the street seems to work fine.
1 - Buy a HILUX housing without ADD, strip your centre out and put it in the new housing. You'll need manual hubs and thats it. There are 2 wires to the FRONT of the diff, just bridge them and you trick the transfer allowing it to engage. The vaccum lines you can just loop in the engine bay and run a short piece to bridge them together.
2 - If you have solenoids playing up, i have 2 complete ADD housings that are in good nick with spare open centres for sale... both have been pulled apart and checked and everything looks great.
I've just taken route 1, and everything seems to be working fine. I haven't had it in the bush yet but testing it on the street seems to work fine.
Who is online
Users browsing this forum: No registered users and 18 guests