We are in production finally
NZ made Billet steel Toyota Hi Steer arms for $550 NZD per pair
http://www.atsl.co.nz/information.php?info_id=6
A few pics of the arms in production
We can DHL them to Sydney for example for an additional $200 NZD or so.
I havn't looked at any other shipping method as yet, but surface may be cheaper.
Please note these are machined from a solid block of tool steel (P20), not cast, or bent or machined by some uninterested Chinese poorly paid worker, they are tough as f@#k steel, the kingpin spigot is pressed in then capscrewed. The arms are in the process of being certified for use on public roads in NZ.
Order up
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Billet HI STEER arms made in NZ
Moderators: toaddog, Elmo, DUDELUX
Billet HI STEER arms made in NZ
'85 Hilux 3rz, duals, 4.7's,6stud histeer,Racerunners up front, coils rear , 30spl longs, on 40" Iroks
[url=http://www.snr4x4.co.nz][size=200][color=red][i]SNR4x4[/i][/color][/size][/url]
[url=http://www.snr4x4.co.nz][size=200][color=red][i]SNR4x4[/i][/color][/size][/url]
First up .. $200NZD to get em shipped over .. i will fly over take a holiday and pick up half a dozen sets and make my money back hand delivering em around Aus when I get home.
Look very neat, can you do the hole for the tie rods etc (not shown in pic)
Look very neat, can you do the hole for the tie rods etc (not shown in pic)
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Road Ranger
product looks tops, but $550 plus $200 for shipping will prolly be a little picy for most, I would try and get someone over here to take them on and sea freight a few of them over, they should cut the cost quite a bit
If the above post did not offend you in any way please PM me so I can try harder!!
Congrats they are a nice set of arms, it is great to see someone at last going to the effort of counterboring/spigoting the kingpin in place, 99% of the $hit arms we get here in oz are all just bolted onto the flat and this is the most common point of failure and problems associated with bent or snapped studs.!!!!!
WWW.TEAMDGR.COM
WWW.SUPERIORENGINEERING.COM.AU
WWW.LOCKTUP4X4.COM.AU
WWW.SUPERIORENGINEERING.COM.AU
WWW.LOCKTUP4X4.COM.AU
1MadEngineer wrote:Congrats they are a nice set of arms, it is great to see someone at last going to the effort of counterboring/spigoting the kingpin in place, 99% of the $hit arms we get here in oz are all just bolted onto the flat and this is the most common point of failure and problems associated with bent or snapped studs.!!!!!
The other problem with them is the tapper hole for the cones is to deep and the washers that go top of the cones tighten up on the arms and not the cones as the cones are shallower then the tapper. Does that make sense
Who is online
Users browsing this forum: No registered users and 1 guest