Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

100 Series Front Leading Arms

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 114
Joined: Mon Feb 12, 2007 8:55 pm
Location: Sunny Coast

100 Series Front Leading Arms

Post by Gazza the Chippy »

Hey fellas, looking for some help, the front leading arm has broken the mount on the diff, causing it to leak somewhat. Is it poss to weld this back together or will it weaken the diff housing. Thanks Gazza.

Should've kept the wheels on the ground I spose. :armsup:
Gazza the Chippy
Top
Posts: 305
Joined: Mon Oct 17, 2005 10:22 am
Location: BRISVEGAS

Contact:
Contact JOHNZ

Post by JOHNZ »

Course you can. Weld it & add some bracing to prevent it happening again
LOVELLS-EFS-DOBINSON-PROCOMP-BILSTEIN-KONI-RANCHO-TOUGHDOG-BLUEMAX
COIL SPACERS from $46pr
4WD SUSPENSION & BODYLIFTS 0418780611 A/H PH/FAX 07 33512692 - www.zordos4wdsuspension.com.au
Top
Posts: 2404
Joined: Fri Jul 07, 2006 9:00 pm
Location: Ipswich

Post by Sic Lux »

Probably best to pull it apart and clean it out and heat with oxy and weld it with it hot, PM rover1 about it he was saying that's the propper way to do it we welded up a crack in my rear housing.
plenty of parts on the bench
Top
Posts: 114
Joined: Mon Feb 12, 2007 8:55 pm
Location: Sunny Coast

Post by Gazza the Chippy »

Thanks fellas, Need to get it sorted ASAP going to cruiser for queens pi##up next weekend. Gazza!
Gazza the Chippy
Top
Posts: 2097
Joined: Tue Aug 12, 2003 6:50 pm
Location: wollongong

Post by dow50r »

Get someone with a mig to zap it up and add gussets. Take out the noelathane and put rubber back in...less stress....quite a few options, flip arm brackets if you have high lift, x link if it is cracked up front...that removes the front of the brackets either side....caster plates strengthens it all up if you put rubber back in.and better flex.
Andrew
Top
Posts: 114
Joined: Mon Feb 12, 2007 8:55 pm
Location: Sunny Coast

Post by Gazza the Chippy »

Got the old girl fixed today, welded it backup and added strength to it. Can you get offset bushes in rubber, will look into it. Gazza!
Gazza the Chippy
Top
Posts: 2097
Joined: Tue Aug 12, 2003 6:50 pm
Location: wollongong

Post by dow50r »

you put std back in and slot the front hole 14mm for 2 degrees.
Top
Posts: 114
Joined: Mon Feb 12, 2007 8:55 pm
Location: Sunny Coast

Post by Gazza the Chippy »

Thanks, they're holding up at the moment, when they flogg out I'll change it over. The weld job held up with some severe puishment at Landcruiser on the weekend. Gazza!
Gazza the Chippy
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 0 guests