Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Leaf Spring over Axle Conversion on a BJ40

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 12
Joined: Thu Oct 23, 2003 5:31 pm
Contact:
Contact Fat Git

Leaf Spring over Axle Conversion on a BJ40

Post by Fat Git »

How/What to mount Tie Rod to left Steer Arm? - Do Nothing, As the Bump Steer is'nt too bad? :?

Where to buy Spring Perches? - Not from the incredible exspensive 4WD shops, such as Big Balls Offroad :x

Where to buy 6" longer Brake Lines, Also for the Proportioning Valve?

Where to buy Square U-Bolts?

What else :?: :roll:
Top
Posts: 12
Joined: Thu Oct 23, 2003 5:31 pm
Contact:
Contact Fat Git

Post by Fat Git »

So, Can I safely assume that no one on this entire Forum knows anything about performing a Leaf Spring over Axle Conversion? :bad-words:
Then why does it appear that some people have this Modification on their Vehicles, But no one know how? :rofl:
Top
Posts: 5457
Joined: Sun Oct 27, 2002 9:49 am
Location: Sydney

Post by Shorty40 »

Fat Git wrote:So, Can I safely assume that no one on this entire Forum knows anything about performing a Leaf Spring over Axle Conversion? :bad-words:
Then why does it appear that some people have this Modification on their Vehicles, But no one know how? :rofl:


Never assume grasshopper ;)

Give it time dude, your post has been on for about 12 hours or so :roll:

Your questions will no doubt be answered in time - be patient ;)

Dan
Top
Posts: 5457
Joined: Sun Oct 27, 2002 9:49 am
Location: Sydney

Re: Leaf Spring over Axle Conversion on a BJ40

Post by Shorty40 »

Fat Git wrote:How/What to mount Tie Rod to left Steer Arm? - Do Nothing, As the Bump Steer is'nt too bad? :?

Where to buy Spring Perches? - Not from the incredible exspensive 4WD shops, such as Big Balls Offroad :x

Where to buy 6" longer Brake Lines, Also for the Proportioning Valve?

Where to buy Square U-Bolts?

What else :?: :roll:


See :D


I have a double flipped arm on the passenger side - works well for me.

Spring Perches and U Bolts - Where are you ? M&M Custom (Mick or Matt), Dave Camp (trail tough), Sam Keck (Overkill) etc

Brake lines - not sure :?

If you go spring over its a good idea to cut and rotate the knuckles to get your geometry back close to standard ;)

Also, a shacklereversal is a good idea at the same time (you may aswell if everythingis already out :lol: )

Dan
Top
Posts: 13555
Joined: Fri Nov 15, 2002 1:28 pm
Location: Melbourne

Post by grimbo »

search :D before jumping up and down
Ransom note = demand + collage
Top
Posts: 3299
Joined: Fri Nov 08, 2002 8:28 am
Location: Sydney

Post by spazbot »

Dont be a tight arse, unless you wanna buy some RHS and cut your own perches that is what your going to pay
www.overkill4x4.com
ph 94766137
Top
Posts: 12
Joined: Thu Oct 23, 2003 5:31 pm
Contact:
Contact Fat Git

Post by Fat Git »

If I bought the exspensive Spring Perches, Would there be one that'll fit where the Diff slightly intrudes for the front right?
Top
Posts: 3299
Joined: Fri Nov 08, 2002 8:28 am
Location: Sydney

Post by spazbot »

Call ryan at snake racing direct 95701588
im sure they will have the bit you need, might get it a little cheaper aswell
www.overkill4x4.com
ph 94766137
Top
Posts: 12
Joined: Thu Oct 23, 2003 5:31 pm
Contact:
Contact Fat Git

Post by Fat Git »

Does Toyota sell Spring Perches? - As the front right underneith the Axle looks like it would be a good fit above.
Would a normal Suspension shop sell Spring Perches?

I think the Brake Lines should be long enough, But the Proportioning Valve Line is very close now, So I would want to get one that is atleast 6" longer. Would I have to get it custom made or do they all use the same fitting and could get one from the Parts Store?
Top
Posts: 98
Joined: Sat Jul 12, 2003 9:28 pm
Location: victoria

Post by 60serius »

Fat git if you want to be a real tight arse you can grind off the original
spring purches and reuse them and the diff side one will have the cut out
already done.
The brake lines can be made up by ABS or a brake specialist in your state
Top
Posts: 13555
Joined: Fri Nov 15, 2002 1:28 pm
Location: Melbourne

Post by grimbo »

fat git surely you can do better with your avatar than stealing the pic from the outerlimits home page :roll:
Ransom note = demand + collage
Top
Posts: 428
Joined: Tue Oct 22, 2002 8:26 am
Location: The Sovereign Nation of Sealabia

Post by 2car »

Go to http://www.ih8mud.com and look under 'Technical Links'. It's the closest you'll get to 'Springovers for Dummies' :finger:
74 FJ40, 307, Hilux DBC, 35 Claws, welded rear.

'''_ ______
'/|_[_____]__
|?[_L/-\_|o=o|_
?:__;-?__-,==,_
()_)O()_)O== )_)
Top
Posts: 15549
Joined: Tue Oct 22, 2002 9:23 am
Location: Your Mummas House!

Contact:
Contact bj on roids

Post by bj on roids »

never performed one, dont know anything about them apart from the fact that they are illegal in queensland or something?
hands and mums dont count!!!
Top
Posts: 12
Joined: Thu Oct 23, 2003 5:31 pm
Contact:
Contact Fat Git

Post by Fat Git »

2car wrote:Go to http://www.ih8mud.com and look under 'Technical Links'. It's the closest you'll get to 'Springovers for Dummies' :finger:

I've known about Ih8mud.com for so long I remember when Woody had it on the Birfield.com Server and it has gone back to it three days ago. :shock:
Top
Posts: 2149
Joined: Sun Oct 20, 2002 6:59 pm
Location: gold coast, australia

Contact:
Contact NICK

Post by NICK »

Fat Git wrote:Does Toyota sell Spring Perches? - As the front right underneith the Axle looks like it would be a good fit above.
Would a normal Suspension shop sell Spring Perches?

I think the Brake Lines should be long enough, But the Proportioning Valve Line is very close now, So I would want to get one that is atleast 6" longer. Would I have to get it custom made or do they all use the same fitting and could get one from the Parts Store?



you are kidding yourself right? you dont want to spend the money big balls is asking then want to know if toyota sell them. you are trying to scam your way around brake lines, all good till you take your poser rig out and snap one of at the same time your drive shaft pulls apart because you didnt want to send the $$$ there.


NICK
TECH SCREW GURU
Top
Posts: 2149
Joined: Sun Oct 20, 2002 6:59 pm
Location: gold coast, australia

Contact:
Contact NICK

Post by NICK »

bj on roids wrote:never performed one, dont know anything about them apart from the fact that they are illegal in queensland or something?


thats true, you watched someone else do it :finger: :finger:
TECH SCREW GURU
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 8 guests