Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Maverick running pretty bad.

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Forum rules
Post Reply
Posts: 443
Joined: Tue Jan 04, 2005 10:08 pm
Location: sydney

Maverick running pretty bad.

Post by mattsluxtruck »

Hi all
I have a duel fuel 4.2 carby Maverick. Was running ok but not great.
Fitted a Pertronix yesterday and a GT40 coil , started it up. Was idling heaps better and starting easier. All seemed good.
Took it for a drive this evening and the problems started.
Straight away when I hit 3800revs it started surging , missing and a couple of pops out the exhaust. This was on LPG. Turned it over to Petrol same thing happened.
Took it for a bit of a drive , found the temp was starting to climb a bit and the higher the temp got the worse the running was. It was starting to miss around 3000.
Got it home ok and free reved it to 3500 miss and stumble was there.
I know its not fuel related because it does it on both LPG and Petrol.
So it is missing both free reving and under load. Idle seems fine and it pulls well up until 3000. It is easy to start too.
I have not touched the timing because I didnt pull the dizzy out of the truck to fit the Pertronix.
Any ideas where to start looking? I thought if it was an electrical drama it would be there all the time not just higher in the rev range.
The cap , leads and plugs are still the original items from the old points setup. There didnt seem to be a problem before.
This one has me scratching my head!
Any ideas or help appreciated.
Matt
Top
Posts: 1152
Joined: Mon Sep 25, 2006 8:25 pm
Location: the most livable planet in the universe

Post by its aford not a nissan »

you did reset the timiung after fitting it didnt you
Top
Posts: 443
Joined: Tue Jan 04, 2005 10:08 pm
Location: sydney

Post by mattsluxtruck »

As i posted up the top in the description of the problem I have not touched the timing because I never removed the dizzy or adjusted the timing when I fitted the Pertronix.
Top
Posts: 335
Joined: Mon Oct 10, 2005 10:33 pm
Location: newcastle

Post by xenith »

i would say that the coil is not up to it mate
it will go or it will blow
Top
Posts: 443
Joined: Tue Jan 04, 2005 10:08 pm
Location: sydney

Post by mattsluxtruck »

I hope it aint a coil problem. Its a new GT40 like they recommend with the Pertronix. Something to look at but.
Top
Posts: 1258
Joined: Wed Mar 21, 2007 7:49 pm
Location: Mornington/ Victoria

Contact:
Contact PGS 4WD

Post by PGS 4WD »

A GT40 or GT40R? Have you bypassed the ballast resistor? The GT40r is a low voltage coil designed for a ballast, unfortunatly the Nissan ballast is specific to the Nissan coil, you should buy a generic ballast if using a GT40r or you should bypass the ballast if using a GT40(12v) coil.

Joel
-Pre trip inspections/ servicing
-Suspension/ custom modifications
-4wd Dyno & tuning
-Qualified mechanics
Top
Posts: 443
Joined: Tue Jan 04, 2005 10:08 pm
Location: sydney

Post by mattsluxtruck »

Its just a standard GT40. The ballast has ben bypassed and removed. After talking to a few people Im thinking the timing may be too advanced. I have never touched it since I bought it so who knows what it was set up on.
Top
Posts: 309
Joined: Tue Dec 03, 2002 11:43 am
Location: SOMEWHERE IN VICTORIA

Post by TUFF MAV »

Check the cap. The extra voltage with electronic ign could be tracking in the cap. Is there a loose wire in the dizzy? I had electronic ign on one of mine & it just stopped & wouldnt go again . Ended up being the cap.

Kyle
BUGGERED IT'S A TOYOTA THING
Top
Posts: 1242
Joined: Fri Oct 17, 2003 8:50 pm
Location: Kanwal

Post by ZOOK60 »

Make shaw that the black wire that origanaly went to the points is not flapping around i have had probs with back firing cutting out and surging with wine. It conked out at a major intersection on tuesday wouldnt start again. Turns out that that black wire was jumping around and earthing out on the dizzy.
P.E.T.A
People eating tasty animals.
Top
Posts: 443
Joined: Tue Jan 04, 2005 10:08 pm
Location: sydney

Post by mattsluxtruck »

ZOOK60 wrote:Make shaw that the black wire that origanaly went to the points is not flapping around i have had probs with back firing cutting out and surging with wine. It conked out at a major intersection on tuesday wouldnt start again. Turns out that that black wire was jumping around and earthing out on the dizzy.
Do ypu mean the little black bridging wire that went from the dizzy body to the points plate? I left that on there and put it back under one of the screws thinking it was an earthing cable and had to be on it.
Top
Posts: 1242
Joined: Fri Oct 17, 2003 8:50 pm
Location: Kanwal

Post by ZOOK60 »

yes i think that is the one mine is now tapped up and cable tied out of the way so it cant earth out any more
P.E.T.A
People eating tasty animals.
Top
Posts: 443
Joined: Tue Jan 04, 2005 10:08 pm
Location: sydney

Post by mattsluxtruck »

Well I think I found the problem. The timing was set at 20 btdc :shock: .
Put that back to 10. Splutter still there and getting warm lifted the radiator cap.................nice little steady stream of bubbles. :cry:
Not happy Jan!
Top
Post Reply

Return to “Nissan”

Who is online

Users browsing this forum: No registered users and 4 guests