has a little bit more rust that wat i expected tho so yeh needs new guards doors etc and some welding work nothing to mayor (i thought
) 
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
My build up 83 LWB Sierra
My build up 83 LWB Sierra
bought the little beast last week
has a little bit more rust that wat i expected tho so yeh needs new guards doors etc and some welding work nothing to mayor (i thought )
has a little bit more rust that wat i expected tho so yeh needs new guards doors etc and some welding work nothing to mayor (i thought
) 98 Vitara 2dr Soft Top
had a big releif when i removed the windscreen only to find no bog work and no rust appart from where it could be seen will most likely need new windscreen tho as has rust on the inside but might still be good for rego but will see
the back bar is covered in bog and rust will need to chop and weld new bar in going to use like 2mm think fla bar bunnings can supply that at a good price as i work there will be getting a wire fed cigwelder from there also to assist in the wellding jobs as the stick weld will be to hot and burn every thing
umm engine works put new points in went ok had no petrol put 10bucks in and the carbie needs a mad clean the guards need to come off and found a small whole of rust on the rear wheel arch which has eaten through the floor but easy fix
umm the front diff needs a sand and a spray?? not sure tho if thats the case might need to get new ones will see and post pics up soon also the brakes and all are rusted bad not worth fixing i think anyway umm rear diff looks or leaf springs are rusted and will need to be changed also the shocks need changing the completly gone. apart from fire wall and the few spots and te bar in the back car seems so far to be in good order very pleased with her so far
managed to get a front cut off a 92 swb got me guards and front clip etc fire wall and anything elese i need
also managed to pck up a complete hard top for the girl for a very good price thanks to butnuckle ( russ ) also who i bought the front cut off cheers
also bonnet has a few holes of rust nothing to bad tho i think at this point in time
the back bar is covered in bog and rust will need to chop and weld new bar in going to use like 2mm think fla bar bunnings can supply that at a good price as i work there will be getting a wire fed cigwelder from there also to assist in the wellding jobs as the stick weld will be to hot and burn every thing
umm engine works put new points in went ok had no petrol put 10bucks in and the carbie needs a mad clean the guards need to come off and found a small whole of rust on the rear wheel arch which has eaten through the floor but easy fix
umm the front diff needs a sand and a spray?? not sure tho if thats the case might need to get new ones will see and post pics up soon also the brakes and all are rusted bad not worth fixing i think anyway umm rear diff looks or leaf springs are rusted and will need to be changed also the shocks need changing the completly gone. apart from fire wall and the few spots and te bar in the back car seems so far to be in good order very pleased with her so far
managed to get a front cut off a 92 swb got me guards and front clip etc fire wall and anything elese i need
also managed to pck up a complete hard top for the girl for a very good price thanks to butnuckle ( russ ) also who i bought the front cut off cheers
also bonnet has a few holes of rust nothing to bad tho i think at this point in time
98 Vitara 2dr Soft Top
lwb project
I saw that one listed on Ebay. "Just needs clear coat" I think it said.
My father was interested in it but after seeing your more detailed pics, I'm glad I steered him off it.
I'm doing the same to an NT LWB myself. Have bobbed my lwb body but not fixed firewall issue yet. Good luck with it. Keep the pics coming. Jas.
My father was interested in it but after seeing your more detailed pics, I'm glad I steered him off it.
I'm doing the same to an NT LWB myself. Have bobbed my lwb body but not fixed firewall issue yet. Good luck with it. Keep the pics coming. Jas.
hey nick, i got another one now so il prob have some spares when i turn the 2 into one.
this one has rego so il prob use up a bit of the rego while im fixing up the red one and then do the engine/box swap and rego it.
this one has rego so il prob use up a bit of the rego while im fixing up the red one and then do the engine/box swap and rego it.
my GUBanzy wrote:Dial up internet.........you'd post something and come back 2 beers later to see if it loaded.
doors i could probably help you out with,
are the shorty doors the same as longys but? mine are hard top too
are the shorty doors the same as longys but? mine are hard top too
my GUBanzy wrote:Dial up internet.........you'd post something and come back 2 beers later to see if it loaded.
looks like you been busy.
il be taking the whole body off mine when i do my engine swap.
proabably just pull the body off, fix whatever needs fixing and then paint it, then swap engines etc.. and stick the body back on
il be taking the whole body off mine when i do my engine swap.
proabably just pull the body off, fix whatever needs fixing and then paint it, then swap engines etc.. and stick the body back on
my GUBanzy wrote:Dial up internet.........you'd post something and come back 2 beers later to see if it loaded.
il post up the new pics there still old buying the welder today or tomorrow at the latest
so also what do you guys think the pics above with the shs in it is 40x40x3mm should i do the 3mm or go all out and do the 4mm only little buit difference couldnt get the channel steve susgested as they said they dont make the size of it
the whole in the drivers side fire wall is allot bigger than i expected but not going to stop now
boosted brakes i got the booster from a 1.3L how do i hook it up?? not to sure
anyone rebuilt a carbie on a 4k corrolla or should i just spend a bit and buy a webber for the thing
also extended shackles they hard to make
cheers nick
so also what do you guys think the pics above with the shs in it is 40x40x3mm should i do the 3mm or go all out and do the 4mm only little buit difference couldnt get the channel steve susgested as they said they dont make the size of it
the whole in the drivers side fire wall is allot bigger than i expected but not going to stop now
boosted brakes i got the booster from a 1.3L how do i hook it up?? not to sure
anyone rebuilt a carbie on a 4k corrolla or should i just spend a bit and buy a webber for the thing
also extended shackles they hard to make
cheers nick
98 Vitara 2dr Soft Top
Nice mate, looks like abit of work to go still but will be very satisfying for you when it's all done.
Extended shackles are easy to make, just need two peices of flat bar 50mm or so wide by at least 5mm thick. measure your orig shackle length, add what extra you need then cut the length. make sure you clamp the two halves together well to drill your holes so they line up exactly. or put a tac weld on them while you drill then take it off after. put the tac right on the corner so then when you clean it all up (round the corners) the tac will come off anyhow. if your really worried about strenght, you can weld in a cross peice sort of like making a "H".
I used a H when i made mine for an old pajero years ago, but am just using two straight peices for the Zook.
Keep up the work mate it'll be nice when your all done.
Tim
Extended shackles are easy to make, just need two peices of flat bar 50mm or so wide by at least 5mm thick. measure your orig shackle length, add what extra you need then cut the length. make sure you clamp the two halves together well to drill your holes so they line up exactly. or put a tac weld on them while you drill then take it off after. put the tac right on the corner so then when you clean it all up (round the corners) the tac will come off anyhow. if your really worried about strenght, you can weld in a cross peice sort of like making a "H".
I used a H when i made mine for an old pajero years ago, but am just using two straight peices for the Zook.
Keep up the work mate it'll be nice when your all done.
Tim
He means its really rusty.
Red_Zook is right- to avoid confusion, it's probably best to move the build thread to the members area where it belongs and leave the tech questions on here.
I'll ask a tech question though - how have you resolved the issue of registering the car with the 4K in it?
Steve.
Red_Zook is right- to avoid confusion, it's probably best to move the build thread to the members area where it belongs and leave the tech questions on here.
I'll ask a tech question though - how have you resolved the issue of registering the car with the 4K in it?
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Who is online
Users browsing this forum: No registered users and 46 guests