i need this motor!
http://www.cardomain.com/ride/2122415
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
turbo rocky?
Moderator: Tiny
Thats not a bad unit...
There's a turbo HD engined ( non nitrous ) one making 320KW at the wheels.... was in a performance mag last year ( ??? ).
But these engines woud make very poor 4WD engines, so as a dream great - as reality, not for me.
There's a turbo HD engined ( non nitrous ) one making 320KW at the wheels.... was in a performance mag last year ( ??? ).
But these engines woud make very poor 4WD engines, so as a dream great - as reality, not for me.
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
Standard Applause HD-E cam specs
Exh 43°/1° 224° 0.310" .012"
In 2°/48° 230° 0.327" 0.01"
rocker ratio 1.5
The Applause cam is just slightly more aggressive than the Feroza, but trades off a little low end torque - most people wouldn't feel any great difference. Now if you want to go wilder......
Standard HD-EG Detomaso cam specs
Exh 52°/8° 240° 0.310" 0.012"
In 8°/52° 240° 0.325" 0.01"
rocker ratio 1.5
Exh 43°/1° 224° 0.310" .012"
In 2°/48° 230° 0.327" 0.01"
rocker ratio 1.5
The Applause cam is just slightly more aggressive than the Feroza, but trades off a little low end torque - most people wouldn't feel any great difference. Now if you want to go wilder......
Standard HD-EG Detomaso cam specs
Exh 52°/8° 240° 0.310" 0.012"
In 8°/52° 240° 0.325" 0.01"
rocker ratio 1.5
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
Take a standard one out of any HC or HD engine, take it to a cam grinder, give them the specs and some $$$ and there you have it.
IMO, don't regrind your standard cam, as you may want to change back.
Please note I am not sugesting this as a suitable cam - simply its about the wildest "standard" road cam that Daihatsu put in an H series engine.
I am running a DeTomaso based engine in my Feroza, but have a much milder cam fitted. - but with higher compression. It sort of happened by accident, the old one died, I am slowly building a supercharged engine, which of course wasn't ready and didn't want to use my "good" bits so the Detomaso stuff I had got recycled.
IMO, don't regrind your standard cam, as you may want to change back.
Please note I am not sugesting this as a suitable cam - simply its about the wildest "standard" road cam that Daihatsu put in an H series engine.
I am running a DeTomaso based engine in my Feroza, but have a much milder cam fitted. - but with higher compression. It sort of happened by accident, the old one died, I am slowly building a supercharged engine, which of course wasn't ready and didn't want to use my "good" bits so the Detomaso stuff I had got recycled.
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
can you run to the scrap yard and grab me a cam you reckon?Yes I have about six spare standard cams and can get more , but just in case your serious freight would be far more than a second hand locally sourced cam.
I usually pay about $15Au for a cam on its own - although I have to get it out. Depending on the grind I need it can cost around $100 to $250AU.
The H series engine was not only used in the Feroza it was fitted to the Applause and Charade passenger cars. As long as its an H series engine then the cam will be fine as a donor for a regrind.
So try local first, but if you really really want a cam, and are prepared to pay the shipping I can help.
IF you still want one PM me.
I usually pay about $15Au for a cam on its own - although I have to get it out. Depending on the grind I need it can cost around $100 to $250AU.
The H series engine was not only used in the Feroza it was fitted to the Applause and Charade passenger cars. As long as its an H series engine then the cam will be fine as a donor for a regrind.
So try local first, but if you really really want a cam, and are prepared to pay the shipping I can help.
IF you still want one PM me.
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
Who is online
Users browsing this forum: No registered users and 2 guests