Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
re:lacking power.....
Moderator: Tiny
re:lacking power.....
thanks for replies......just disconected fuel line from filter to injector side.......cranked over engine ..........fuel pumped out but i do not have a pressure gauge to check..........fuel quantity that pumped out seemed enough...ie not a little amount.......i know this isn't accurate enough info..........ps i also have spark present........which leaves me to think injectors or something more sinister in the engine.correct if i'm wrong..but if the engine is running and then suddenly stops and then doesn't start.....chances of all injectors failing is remote?????? isn't it????? thanks
Ok, I'll invite critics, but petrol combustion, 4 stroke engines require, (1) compression,
(2) ignition and (3) fuel. You have apparently confirmed your motor is receiving fuel reasonably consistently. at least for test purposes Assuming your motor is not entirely worn out/ tired/ and has correct ignition, it should function... providing other unfortunate things are not occurring. For example you could have a cracked cylinder block or head/gasket. These will cause your motor to run very poorly. You would be describing major engine overheating issues also, if this was the case.
I am describing pretty basic stuff that might be wrong, it could be that more difficult issues are causing your problems. It is really difficult to diagnose this stuff on line. You would be advised to seek qualified assistance at your local garage/workshop.
(2) ignition and (3) fuel. You have apparently confirmed your motor is receiving fuel reasonably consistently. at least for test purposes Assuming your motor is not entirely worn out/ tired/ and has correct ignition, it should function... providing other unfortunate things are not occurring. For example you could have a cracked cylinder block or head/gasket. These will cause your motor to run very poorly. You would be describing major engine overheating issues also, if this was the case.
I am describing pretty basic stuff that might be wrong, it could be that more difficult issues are causing your problems. It is really difficult to diagnose this stuff on line. You would be advised to seek qualified assistance at your local garage/workshop.
Really need to just add to your original post - not start another one...
OK - assuming you have fuel pressure and spark.
If you put the tip of a screwdriver on an injector and put your ear on the handle end, you should be able to hear the injectors clicking as you wind the engine over.
No clicking then no injection. If your getting diagnostic codes from the computer then its still working so there's hope
Check all the fuses associated with the injection system. Main EFI fuses must be OK as the fuel pump runs. IIRC the injector fuses and control relays are in a black box in front of the battery - lid has clips to keep it on and the components ID's are printed on the outside.
OK - assuming you have fuel pressure and spark.
If you put the tip of a screwdriver on an injector and put your ear on the handle end, you should be able to hear the injectors clicking as you wind the engine over.
No clicking then no injection. If your getting diagnostic codes from the computer then its still working so there's hope
Check all the fuses associated with the injection system. Main EFI fuses must be OK as the fuel pump runs. IIRC the injector fuses and control relays are in a black box in front of the battery - lid has clips to keep it on and the components ID's are printed on the outside.
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
Who is online
Users browsing this forum: No registered users and 1 guest