Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
suzuki jimny
suzuki jimny
im going with a mate to look at a jimny for him, what should i look out for that is suzuki or jimny specific? good and bad point appreciated
[quote="Barnsey"]
Bronwyn Bishop does it for me.[/quote]
Bronwyn Bishop does it for me.[/quote]
Posts: 396
Joined: Fri Dec 24, 2004 4:05 pm
Joined: Fri Dec 24, 2004 4:05 pm
Location: in the shed cutting/grinding/welding mocks old shit vic
just look for scratch's on the chassis noear the rear control arm mount, they get hooked up on this all the time. so if it's done some real 4wding there will be marks.
it will have flogged out wheel bearings on the front, and these will have choo'd out the hubs and stubs. they all do it. so see if there are any recipts for work done.
cheack the rear wheel bearings as these are weak as piss, if its been used, they'll need replacing as will the rear break shoes
the front auto hubs fail all the time, if the 4x4 light is flashing there is most likely an air leek (easy to fix). but if the front wont spin-up, then the problem can be real hard to track down. easy way is to fit manual hubs then the problem is gone forever
if its a G series motor the cam sensor can give issues, this is known by Suzuki, the sensors are cheap and easy to replace
if its a M series motor the ckank sensor will make the car "sluggish" like its not getting enough fuel. this is also known by suzuki.
the CV's are made of glass, as is the rear diff, all the rear diffs in the wreakers have broken pinions, this can be caused by the "cross pins" Floating and catching the pinion on the way past.
check the control arms to see if they are streight, some people have bent them, and i think that mine has a "wave" in it.
if its a series 1 (G motor) also check the front shock mounts on the diff as these "rip off" easy, this was later fixed with the series 2.
the bushes in the front pan hard rod flogg out and will give a "funny" knocking sound at low speed manuvers with full lock one way then the other.
there is more but i just can't think of it right now.
happy hunting
Mitch
it will have flogged out wheel bearings on the front, and these will have choo'd out the hubs and stubs. they all do it. so see if there are any recipts for work done.
cheack the rear wheel bearings as these are weak as piss, if its been used, they'll need replacing as will the rear break shoes
the front auto hubs fail all the time, if the 4x4 light is flashing there is most likely an air leek (easy to fix). but if the front wont spin-up, then the problem can be real hard to track down. easy way is to fit manual hubs then the problem is gone forever
if its a G series motor the cam sensor can give issues, this is known by Suzuki, the sensors are cheap and easy to replace
if its a M series motor the ckank sensor will make the car "sluggish" like its not getting enough fuel. this is also known by suzuki.
the CV's are made of glass, as is the rear diff, all the rear diffs in the wreakers have broken pinions, this can be caused by the "cross pins" Floating and catching the pinion on the way past.
check the control arms to see if they are streight, some people have bent them, and i think that mine has a "wave" in it.
if its a series 1 (G motor) also check the front shock mounts on the diff as these "rip off" easy, this was later fixed with the series 2.
the bushes in the front pan hard rod flogg out and will give a "funny" knocking sound at low speed manuvers with full lock one way then the other.
there is more but i just can't think of it right now.
happy hunting
Mitch
[quote="Gwagensteve"]
nope, apparently I hate suzukis so nobody should be surprised by that :roll:
Steve,[/quote]
[url=http://vic.suzuki4wd.com/]Suzuki 4WD club VIC[/url]
nope, apparently I hate suzukis so nobody should be surprised by that :roll:
Steve,[/quote]
[url=http://vic.suzuki4wd.com/]Suzuki 4WD club VIC[/url]
Doublepost
Last edited by Gwagensteve on Sat Jan 12, 2008 8:05 am, edited 1 time in total.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
lol
Posts: 396
Joined: Fri Dec 24, 2004 4:05 pm
Joined: Fri Dec 24, 2004 4:05 pm
Location: in the shed cutting/grinding/welding mocks old shit vic
hell no!
they drive all right, they are a bit nose heavy, and tend to sit on the front. good for climbing but can be real scary coming down and on serious off-cambers. you will get used to it though.
you won't get used to breaking CV's, i've done 4 in the last 4 trips
, there are no second hand ones in Melb, 'cause i've eaten them . there is no upgrade without doing custom work. i bought a sierra because of the front end issues, however i do know how to up-grade the front, but it'll have to wait until my sierra is finished.
a 30" tire is a Sensible tire any more and you will break shit.
you will want gearing and lockers, they work well with a front locker, better than only having a rear.
Mitch
they drive all right, they are a bit nose heavy, and tend to sit on the front. good for climbing but can be real scary coming down and on serious off-cambers. you will get used to it though.
you won't get used to breaking CV's, i've done 4 in the last 4 trips
, there are no second hand ones in Melb, 'cause i've eaten them . there is no upgrade without doing custom work. i bought a sierra because of the front end issues, however i do know how to up-grade the front, but it'll have to wait until my sierra is finished.a 30" tire is a Sensible tire any more and you will break shit.
you will want gearing and lockers, they work well with a front locker, better than only having a rear.
Mitch
[quote="Gwagensteve"]
nope, apparently I hate suzukis so nobody should be surprised by that :roll:
Steve,[/quote]
[url=http://vic.suzuki4wd.com/]Suzuki 4WD club VIC[/url]
nope, apparently I hate suzukis so nobody should be surprised by that :roll:
Steve,[/quote]
[url=http://vic.suzuki4wd.com/]Suzuki 4WD club VIC[/url]
Posts: 396
Joined: Fri Dec 24, 2004 4:05 pm
Joined: Fri Dec 24, 2004 4:05 pm
Location: in the shed cutting/grinding/welding mocks old shit vic
Gee-zuss... after reading the list of issues they have, I must've been very lucky with Stimpy 
Only real problems were the little air line for the front hub going once - quick fix with $2.00 worth of tube - and the rear bearing going, causing the axle to drift out (caused by using a non-genuine bearing).
No torn shock mounts or CV issues... and Podge used to give Stimpy a pretty hard time of it offroad...
He did have the usually crank sensor hiccup that all Series 1 had, and the water pump went at 90k... but nothing else really
Stimpy always felt tippy on angles, but a 3" bodylift and 4" suspension will do that.
Only real problems were the little air line for the front hub going once - quick fix with $2.00 worth of tube - and the rear bearing going, causing the axle to drift out (caused by using a non-genuine bearing).
No torn shock mounts or CV issues... and Podge used to give Stimpy a pretty hard time of it offroad...
He did have the usually crank sensor hiccup that all Series 1 had, and the water pump went at 90k... but nothing else really
Stimpy always felt tippy on angles, but a 3" bodylift and 4" suspension will do that.
DRS smells like a cat-food milkshake... and wet socks... and gorgonzola cheese... all whizzed up in a blender
From what I have seen of Mugginsmoo's and others, they are happy on a 30" tyre and with some subtle guard work will run that tyre with very little lift. With a locker, they are quite capable.
IMHO get an auto, they're a good little auto and having it will reduce the need to regear the transfer case (expensive) or fit a gear drive case from a sierra and regear that (not expensive, but fiddly and difficult to get 100%)
Muggins is right that they work well with a front locker, but my take on this is that that loads the CV's more heavily, and they are both weak and hard to find.
Just my 2C
Steve.
IMHO get an auto, they're a good little auto and having it will reduce the need to regear the transfer case (expensive) or fit a gear drive case from a sierra and regear that (not expensive, but fiddly and difficult to get 100%)
Muggins is right that they work well with a front locker, but my take on this is that that loads the CV's more heavily, and they are both weak and hard to find.
Just my 2C
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Here's a photo from a recent trip we did with Muggins... It's a photo of the rear diff and CV....suzuki boy wrote:Been out with mugginsmoo and it suprised me alot! His is set up VERY well...... Do you want some pics of that trip up mugginsmoo?
Seriously, Muggins car is very capable, but he has had a horrendous run of failures for the gearing and tyre size he's running. As he says, at about a 30" tyre and respecting the car it's fine. If you want to run with built sierras though, they turn to glass.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Posts: 396
Joined: Fri Dec 24, 2004 4:05 pm
Joined: Fri Dec 24, 2004 4:05 pm
Location: in the shed cutting/grinding/welding mocks old shit vic
i'm thinking that the sierra stuff i have will look like that after a few runs in DOOF.
Suziki boy, i'd love some pics
want33s, thay will still run with a crook crank sensor, but they won't run well. that cam sensor tells that coils when to fire. and the crank sensor gets the timing exact.
with a bad crank sensor, they feel as if they have run out of fuel, they have no guts, well even less that the 13 Squirrels they normaly have
Suziki boy, i'd love some pics
want33s, thay will still run with a crook crank sensor, but they won't run well. that cam sensor tells that coils when to fire. and the crank sensor gets the timing exact.
with a bad crank sensor, they feel as if they have run out of fuel, they have no guts, well even less that the 13 Squirrels they normaly have
[quote="Gwagensteve"]
nope, apparently I hate suzukis so nobody should be surprised by that :roll:
Steve,[/quote]
[url=http://vic.suzuki4wd.com/]Suzuki 4WD club VIC[/url]
nope, apparently I hate suzukis so nobody should be surprised by that :roll:
Steve,[/quote]
[url=http://vic.suzuki4wd.com/]Suzuki 4WD club VIC[/url]
Stimpy occassionally "hiccuped" under load... but no other dramas. It never really bothered me, I just pushed in the clutch and tapped the accelerator, released the clutch and it stopped.spamwell wrote:so what happens when the crank sensor fails?? i have a g13bb in my sierra just interested at what i should look out for.
Sam
DRS smells like a cat-food milkshake... and wet socks... and gorgonzola cheese... all whizzed up in a blender
Heres the pics of mugginsmoo on about 31's i think?
Drove out of this! Done the same in mine with some body damage!
Just when he broke a rear axel! Lucky he had a spare and had it changed in about 15 minutes!
Thats all i got of that trip hopefully wheel with you again when i'm in the club!
Drove out of this! Done the same in mine with some body damage!
Just when he broke a rear axel! Lucky he had a spare and had it changed in about 15 minutes!
Thats all i got of that trip hopefully wheel with you again when i'm in the club!
Built swb sierra, building a lwb sierra ute and have a dmax for family camping
4 inch with 31 hmm a reef you need to visit us at suzuki club. We can show you other ways to setup a jimny and share ideals etc. I'm with others hmm. 30's with gearing and locked would be very nice. I've got 30 and the rear locked and had no problems. If you do locked both end gearing WILL be needed. Mugginsmoo knows his jims do read what he has the say.a reef wrote:This is my Jimny, it can go where the Big Toys go, sometimes it leaves the big toys wondering at the bottom of a hill, or in a bog hole, and it will Just keep going.
It has a 4 inch lift, heavy duty control arm and the secret weapon, an ARB rear air locker + 31" maxxis trepadore M/T's.
[/img]
Rob
http://vic.suzuki4wd.com/forum/index.php
www.jimny.se
www.jimny.se
Jimny's are Great little 4wd's when you compare apples with apples they rate well, remember, someone like Mugginsmoo, would have a long list of breakages cause he probably is often the one in a group who will drive the furthest up a track, the soccer mum with the jimny could do over 200000 km's to the field with just services in a jim. everything has its faults. in the 8 years of driving my jim my list of breakages come close to Mugginsmoo, the places I've dragged that little car I'm not supprised so many things have broken. saying that, a mate with a heavily modded Landcruiser Tray back has a brakage list just as long as mine, but his repair bills in most cases are double. If ya gonna play prepare to pay.
yes, gman79au i agree with your comment. If we push ourselves and the cars over the usuall limits, everything is always expected to break or bend, etc. Even if we replace the weakest parts in the vehicles with the strongest available, something else will always break. But thats' part of offroading. The question is how do we not break anything if we push it to the limit.Jimny's are Great little 4wd's when you compare apples with apples they rate well, remember, someone like Mugginsmoo, would have a long list of breakages cause he probably is often the one in a group who will drive the furthest up a track, the soccer mum with the jimny could do over 200000 km's to the field with just services in a jim. everything has its faults. in the 8 years of driving my jim my list of breakages come close to Mugginsmoo, the places I've dragged that little car I'm not supprised so many things have broken. saying that, a mate with a heavily modded Landcruiser Tray back has a brakage list just as long as mine, but his repair bills in most cases are double. If ya gonna play prepare to pay.
The answer is, STOP BEFORE IT DOES! "choose a different line!" or stop completely and turn back, heheh............ but what fun would that be?
As for macca81, every car has their own good and bad points so look out for anything, but if you buy and build a jimny, you need to build it with the best parts available all at once to stop you from having further problems as you build on. The problem with jimny's is similar to that of the Jeep's, so you must build it completely in the first place.
As i have learned, do not add on as you go. Trust me, it wont work, building it all at once will cost you alot of money and time, but that's the way it is.
OK, say I trust you. Please explain how to build the front end with the best parts available to ensure that CV's and inner axles do not snap like twigs, or are we supposed to know when a CV is going to go before hand and "STOP BEFORE IT DOES"a reef wrote: The answer is, STOP BEFORE IT DOES! "choose a different line!" or stop completely and turn back, heheh............ but what fun would that be?
you need to build it with the best parts available all at once to stop you from having further problems as you build on. The problem with jimny's is similar to that of the Jeep's, so you must build it completely in the first place.
As i have learned, do not add on as you go. Trust me, it wont work, building it all at once will cost you alot of money and time, but that's the way it is.
Mugginsmoo broke a front CV and rear R&P on an obstacle driving gently. I hammered through the same obstacle, all wheels up and giving it hate. Muggins is running about 4:1 transfer, locked front and rear, 32" MTR's. I'm running a 660, 34" swampers, welded rear, and when I hit that obstacle, I already had two cracked teeth on the crownwheel.
The jimny had major breakage with a reasonably small tyre, driven gently.
Please explain how these driveline issues can be overcome by buying more expensive parts?
Judging by your post on the hilux spring thread, it doesn't involve non suzuki parts
:?::?:Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
I've broken a cv in a dirt carpark, I just think of the punishment it was given before hand. 32in tyres are way to big for jimny unless you live in an area where it rains most of the year and all you drive is mud, I've been running stock tyres with 3inch lift 2in body looks stupid but hey not breakages, this is a record since when it was new when it also had stock tyres on it. is there a pattern forming here? I wouldn't go bigger than 215 series tyres of max 30x9.5 keep them narrow.
Who is online
Users browsing this forum: No registered users and 67 guests