Just a quick one...
I finally got around to getting a qoute today...
CARBY 1.6
H.D clutch
NEW RAD
DRIVE IN DRIVE OUT....
About $4,000.... What is the going rate?
Is this a good price?
(i thought it was going to be cheaper)
Thanks if you answer these annoying questions.
Bruno
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
1.6 conversion
1.6 conversion
97 GTI intercld suparchrged Zuk
3+3inch lift
3+3inch lift
Hey mate, if your doing a 1.6l g16 engin into a sierra then im doing same thing at the mom. this is sorta half an answer but gives a litle info. quoted yesterday, JUST for G16B (fuel inj) engin recon $2300. no computer, loom, bell housing/ converter plate or altenator. This quote was b4 they knew i wanted to do a siera engin conv. so was on the assumption they were removing out of vitara then installing there reconed engine back in. there now looking for a computer, loom and all the other stuff for me b4 they do another quote.
not to hijack but does any one know where i can get a loom n computer for the G16B? PM me.
hope it helped mate.
not to hijack but does any one know where i can get a loom n computer for the G16B? PM me.
hope it helped mate.
I paid $500 for my 1.6 with a 1.3 gearbox bolted to it!
just needed leads and a new throwout bearing and sparkplugs.
took me 4 hours to swap the motors.
$4000.
EFI with a turbo and stainless exhaust, with chip work, and possibly port the head.
Then i might think of $4000
not a carby swap over.
should be $1500 to $1800 for basic short rebuilt 1.6 motor.
$75 for mod plate.
$250 new clutch.
$200 new oil and other necessities
My 2c
or if you lived in brisbane you could have it all done by someone else for $2500 to $3000
just needed leads and a new throwout bearing and sparkplugs.
took me 4 hours to swap the motors.
$4000.
EFI with a turbo and stainless exhaust, with chip work, and possibly port the head.
Then i might think of $4000
not a carby swap over.
should be $1500 to $1800 for basic short rebuilt 1.6 motor.
$75 for mod plate.
$250 new clutch.
$200 new oil and other necessities
My 2c
or if you lived in brisbane you could have it all done by someone else for $2500 to $3000
I hate going to weddings because all the grandma's used to poke me in the ribs saying you're next, you're next. They've stopped doing it since I started doing it to them at funerals.
how much they charging you for the plate?tazmanier wrote:bell housing/ converter plate .
or are you suplying it your self?
ya know that benT selld them for $200 posted to your door!
I hate going to weddings because all the grandma's used to poke me in the ribs saying you're next, you're next. They've stopped doing it since I started doing it to them at funerals.
I just put a g16a in a sierra. I paid $700 for a second hand carbi motor. The wreckers want about $1400 for the same, or $2000 for a g16b injected. New Daikin clutch kit was $148 from cheapa auto spares, oil n filter for $15, few different bolts and half a days work. Should b easy under $1000 if u do it urself. Hope this helps 
06 Grand Vitara Prestige, 2" lift, Kumho A/Ts, ARB winch bar, snorkel, spotties. Also a Regal 2150 LSC Volva Penta 350 gsi duoprop, and a kayak ;-)
If they think you are serious about getting them to do the job and show some kind of commitment, they should give you a better price, as they would get 10 customers a day asking how much this or that may cost, so they would just quote off the top of theyre heads without thinking too much about it, as 99% of ppl asking arent serious.
thats about the going rate over here for the conversion sadly.
but if you are only going a carb 1.6 not a mpfi one. then it'l only take a day to do yourself in your driveway with minimal tools.
hire a hoist and stand and go for it. i may be able to give a hand if needed.
btw buy bents apadter kits also. easy to use.
but if you are only going a carb 1.6 not a mpfi one. then it'l only take a day to do yourself in your driveway with minimal tools.
hire a hoist and stand and go for it. i may be able to give a hand if needed.
btw buy bents apadter kits also. easy to use.
[url=http://www.outerlimits4x4.com/viewtopic.php?p=930942#930942&highlight=]Zook[/url]
U SUK Zook Built and Sold.
New rig is 97 80 DX. 2" list 33s
U SUK Zook Built and Sold.
New rig is 97 80 DX. 2" list 33s
Who is online
Users browsing this forum: No registered users and 0 guests