Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Winch cable cut

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 329
Joined: Tue Jun 28, 2005 3:08 pm
Location: Sydney

Winch cable cut

Post by Badass Bundy »

Guys I need to know where I can take my fourby to get 10 metres taken off my winch cable. As of now it rubs hard against my control box and wont wrap around the winch drum properly. So I need someone to cut the cable, and fit the hook to the new end. Where can I take it? I live in Sydney city. Any suggestions?
80 Series 1HD-T
Front and Rear Factory Lockers
Rear drawer system with fridge slide
10,000Lbs Winch
Built for touring
Top
Posts: 1232
Joined: Sun Feb 29, 2004 11:37 pm
Location: Brisvagas

Post by Bad JuJu »

any rigging place will bw able to help out.

Break out the yellow pages.
Posting quality not quantity!

Wanted: Stock HiLux Front Leaf Springs
Top
Posts: 292
Joined: Wed Jan 09, 2008 12:20 pm
Location: Ipswich

Post by hilux79 »

Hey mate no expert on this but I cut the cable at the oppisite end to the hook with a angle grinder and then crimped a new terminall on the end. As the terminal dosen't hold any load.
Ben
Top
Posts: 329
Joined: Tue Jun 28, 2005 3:08 pm
Location: Sydney

Post by Badass Bundy »

hilux79 wrote:Hey mate no expert on this but I cut the cable at the oppisite end to the hook with a angle grinder and then crimped a new terminall on the end. As the terminal dosen't hold any load.
Done! How many metres did you take off?
80 Series 1HD-T
Front and Rear Factory Lockers
Rear drawer system with fridge slide
10,000Lbs Winch
Built for touring
Top
Posts: 4825
Joined: Sun May 04, 2003 6:33 pm
Location: Berwick vic

Post by droopypete »

Badass Bundy wrote:
hilux79 wrote:Hey mate no expert on this but I cut the cable at the oppisite end to the hook with a angle grinder and then crimped a new terminall on the end. As the terminal dosen't hold any load.
Done! How many metres did you take off?
Wouldn't the more relivent questions be what type of winch does he have and how many metres did he leave on?
Cable bracing is the way of the future!

v840 said "That sounds like a booty fab, hack job piece of shit no offence."
Top
Posts: 282
Joined: Tue Apr 15, 2003 12:56 am
Location: Queanbeyan NSW

Post by Matt N »

Badass Bundy wrote:
hilux79 wrote:Hey mate no expert on this but I cut the cable at the oppisite end to the hook with a angle grinder and then crimped a new terminall on the end. As the terminal dosen't hold any load.
Done! How many metres did you take off?
When unscrewing the terminal try to hold the cable against the side of the drum with your other hand. Because of the tight coils in the cable it holds quite a bit of spring.

First time I did this I just started unscrewing, cable flicked out sending the little screw flying, never to be seen again! :oops:
Top
Posts: 292
Joined: Wed Jan 09, 2008 12:20 pm
Location: Ipswich

Post by hilux79 »

droopypete wrote:
Badass Bundy wrote:
hilux79 wrote:Hey mate no expert on this but I cut the cable at the oppisite end to the hook with a angle grinder and then crimped a new terminall on the end. As the terminal dosen't hold any load.
Done! How many metres did you take off?
Wouldn't the more relivent questions be what type of winch does he have and how many metres did he leave on?
It's a 9500lbs warn low mount. I only took a meter off, I was doing it because the termination was not on it when i bought it and the wire had started to fray. I held the cable in a vice when i cut it and it has worked fine.
Ben
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 153 guests