Hi all
i'll be fitting a second battery regulator to the landcruiser, but in between the battery and the items drawing power i'd like to fit some kind of low voltage cutout at say 10.5 - 11 volts so that i give the battery it's best life. Is there anywhere i can get one appropriate with some kind of warning buzzer or monitor display
MILO
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
voltage cutout switch for second battery
Moderator: -Scott-
Posts: 3725
Joined: Wed Jun 30, 2004 1:45 pm
Joined: Wed Jun 30, 2004 1:45 pm
Location: Blue Mountains, or on a rig somewhere in bumf*ck idaho
voltage cutout switch for second battery
http://www.populationparty.org.au/
Hey,
I can get you one, They are rated at 40amps, and can be switched to cut out at either 12v, 11v, or 10v.
I think they are about $50 or $60 dollars
I can get you one, They are rated at 40amps, and can be switched to cut out at either 12v, 11v, or 10v.
I think they are about $50 or $60 dollars
KILLA KUSTOM KABLES
CUSTOM AUTO ELECTRICAL SPECIALISTS
0404811498
LS1 & DURAMAX ENGINE CONVERSIONS, DRIVE IN DRIVE OUT. PATROLS AND CRUISERS
LS1 STANDALONE HARNESS $475ex
CUSTOM AUTO ELECTRICAL SPECIALISTS
0404811498
LS1 & DURAMAX ENGINE CONVERSIONS, DRIVE IN DRIVE OUT. PATROLS AND CRUISERS
LS1 STANDALONE HARNESS $475ex
Re: voltage cutout switch for second battery
I've installed a VSR (Voltage sensitive relay). It's very simple to install, just connect it between the two batteries. When the voltage gets high enough (about 12.8) it connects the two batteries, when they get low (just under 12v) they disconnect. That way the auxillary can be run until flat without affecting the starting battery. Only thing is that when charging they are linked, so its best to get two identical batteries to save any hassles later on. I've bridged the VSR off a solenoid (more capable amps) so if I need to link them together in an emergency I can. The VSR handles 90 amps. It has an LED on the unit to show you when they are linked, but no remote warning. I guess you could mount this small unit somewhere inside if you wanted to, but under the bonnet it works just fine.rockcrawler31 wrote:Hi all
i'll be fitting a second battery regulator to the landcruiser, but in between the battery and the items drawing power i'd like to fit some kind of low voltage cutout at say 10.5 - 11 volts so that i give the battery it's best life. Is there anywhere i can get one appropriate with some kind of warning buzzer or monitor display
MILO
Shut Up, Get Out, & Start Digging...
Posts: 3725
Joined: Wed Jun 30, 2004 1:45 pm
Joined: Wed Jun 30, 2004 1:45 pm
Location: Blue Mountains, or on a rig somewhere in bumf*ck idaho
Posts: 1931
Joined: Sun Jun 22, 2003 10:29 am
Joined: Sun Jun 22, 2003 10:29 am
Location: Everything 4WD, 86 Camms Rd Cranbourne
Contact:
Do you have any more info on these? Specs/pics?killalux wrote:Hey,
I can get you one, They are rated at 40amps, and can be switched to cut out at either 12v, 11v, or 10v.
I think they are about $50 or $60 dollars
I have been looking at getting one of these
http://www.piranhaoffroad.com.au/produc ... sories.htm
My club
www.vfwdc.com
My store
Everything 4WD
86 Camms Road Cranbourne
www.everything4wd.com.au
sales@everything4wd.com.au
Phone: 03 59955055
www.vfwdc.com
My store
Everything 4WD
86 Camms Road Cranbourne
www.everything4wd.com.au
sales@everything4wd.com.au
Phone: 03 59955055
Who is online
Users browsing this forum: No registered users and 1 guest