Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
HELP!Stripped filler plug.
Moderators: toaddog, Elmo, DUDELUX
HELP!Stripped filler plug.
I need help removing a VERY stripped tranfer case filler plug on my hj60.Recently purchased car and have a desire to change oil.(not even sure if it's got oil in it)
what tools and/or skills do you have available?
if you have a MIG the easiest way is to weld a nut to the plug - pick a good sized nut that you can weld through the middle of onto the plug.
if you have a hacksaw and endless patience you can cut a slot into the plug and use a big screwdriver with a shifter on it. no guarantee.
if you have a grinder or even a file you can make new flats on the plug and put a spanner, socket or shifter on it.
you could try drilling it out and using a stud extractor however swarf will probably end up inside the tcase. bad.
you could try just bashing a chisel in the right place to loosen it.
bash on a slightly too small socket.
make sure you use a 6 point socket.
there are probably more options.
if you have a MIG the easiest way is to weld a nut to the plug - pick a good sized nut that you can weld through the middle of onto the plug.
if you have a hacksaw and endless patience you can cut a slot into the plug and use a big screwdriver with a shifter on it. no guarantee.
if you have a grinder or even a file you can make new flats on the plug and put a spanner, socket or shifter on it.
you could try drilling it out and using a stud extractor however swarf will probably end up inside the tcase. bad.
you could try just bashing a chisel in the right place to loosen it.
bash on a slightly too small socket.
make sure you use a 6 point socket.
there are probably more options.
Free air locker to the first 20 callers!
If you get a $20 SuperCrap 100mm grinder and a 1.5mm cutting disk for stainless steel, you can cut a slot in the bolt head.vanners wrote:Good point,i mean the head is VERY rounded.It seems to be some kind of softish metal,perhaps alloy.The best option maybe to try and weld/mig some kind of nut to it,however i'm not equiped to such a job.
The other option is 24" plumbers stilsons. They have a good bight on them and great leverage.
I'm the sharpest tool in the shed!
v6hilux wrote:If you get a $20 SuperCrap 100mm grinder and a 1.5mm cutting disk for stainless steel, you can cut a slot in the bolt head.vanners wrote:Good point,i mean the head is VERY rounded.It seems to be some kind of softish metal,perhaps alloy.The best option maybe to try and weld/mig some kind of nut to it,however i'm not equiped to such a job.
The other option is 24" plumbers stilsons. They have a good bight on them and great leverage.
Hammer and chisel would be my choice. I would say it has an alloy plug in it. If your going to buy a new one make sure its a steel one or go to a wreckers and grab one out of a toyota diff housing as they are all steel and fit the gearbox as well.vanners wrote:Due to the long range fuel tank being about 10cm from the plug access is somewhat limited.No mig.
I know how soft those plugs are and you will really struggle to weld anything to it. If its that tight then your going to need to give it some shock treatment. I think you will be suprised how easy it comes off with a hammer and chisel.vanners wrote:Can you weld onto soft alloy?If so i think welding a nut on and then using a spanner would seem the way to go.ive had a set of locking pilers on it with good grip but it just keeps chewing the plug(whats left of it)away.The plumbers wrench has done the same.It seems very tight.
All is well that ends well!After getting somewhat wet a little abit of swearing,she is out>>>>>Obivously to hard for previous owner,as he had created a little monster.i ended up filling it to make a square and got a 19mm open end spanner and hit it.Have not yet dropped the drain plug but am quite sure it is empty.Think i may run a level hose from the gear box as an insurance.Thanks heaps for all your feedback.Gotta love old trucks and the joy of success.(regardless of its size and importance).I wil try for some photo,s.
Who is online
Users browsing this forum: No registered users and 83 guests