Hi I am building a 89 sierra for my son and it has 31 inch tyres on it and I would like to know if 5.1:1 diff ratios would be to low or would they be ok for road use.
Thankyou Darryl
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
89 sierra diff ratio
They'll be pretty low - expect revs to be up around 4000rpm for cruising with the 31's on - that's about 500rpm higher than stock.
It's OK, but not ideal.
Off road, they're not much chop - crawl runs about 41.1 - nowhere near enough for steep work. (OK for mud though)
Reduction transfer gears are pretty cheap these days. They'd be a better bet if you want to do off road work with it.
5.12's have their place, but if you want to correct road revs, try 4.6 gears from a three speed auto vitara.
Steve.
It's OK, but not ideal.
Off road, they're not much chop - crawl runs about 41.1 - nowhere near enough for steep work. (OK for mud though)
Reduction transfer gears are pretty cheap these days. They'd be a better bet if you want to do off road work with it.
5.12's have their place, but if you want to correct road revs, try 4.6 gears from a three speed auto vitara.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Most ppl ive seen with 5.1 diffs break pinions and crownwheels in real extreem stuff, go the transfer gears cheaper and stronger.
If you want to get real extreem then get a brace ring or cradel for the transfer, several ppl make them or you can buy a calmini off the shelf, makes them very strong
If you want to get real extreem then get a brace ring or cradel for the transfer, several ppl make them or you can buy a calmini off the shelf, makes them very strong
93 NJ,5 speed,2" body lift,32" muddies
There's nuttn like momentum
There's nuttn like momentum
You may well be right, I have seen a 5.12 break, but it was a very old diff that had been badly set up at some stage and had a poor wear pattern on it. (I've seen some tall gears like 3.7's break too though)
Additionally, I have a hunch thrust on the pinion bearings increases with the higher ratios. This compounds the problem if crush sleeves collapsing, loosening bearings, accelerating wear (and seal failure) and leading to failure.
I've seen LOTS of sierra diffs with loose pinions. I have had my front diff setup with a solid spacer to try an eliminate this problem. Fingers crossed!
I reckon it's important to get sierra diffs setup by a professional. Consider it an investment.
Steve.
Additionally, I have a hunch thrust on the pinion bearings increases with the higher ratios. This compounds the problem if crush sleeves collapsing, loosening bearings, accelerating wear (and seal failure) and leading to failure.
I've seen LOTS of sierra diffs with loose pinions. I have had my front diff setup with a solid spacer to try an eliminate this problem. Fingers crossed!
I reckon it's important to get sierra diffs setup by a professional. Consider it an investment.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
go the 5.1's...you'll love em. and steve u have it arse about, you decrease load on the pinion bearings as you go up numerically.
lwb 1.6efi,4sp auto,f&r airlockers,dual t/cases.custom coils.builder of ROAD LEGAL custom suzukis...and other stuff.
CAD modelling-TECH drawings-DXF preparation.
http://www.auszookers.com/index.php
CAD modelling-TECH drawings-DXF preparation.
http://www.auszookers.com/index.php
My reasoning was the smaller pinions have smaller contact surfaces on the ring gear and the angle of the helical cut is larger, so it stands to reason they thrust more.
Steve.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
they are under no-where near as much load [ input power and torque ]to turn say a 31 inch tyre, so the thrust forces are reduced. the thrust forces on a 3.9 with 31's is way more, and combined with a reduction t/case is way more again. the angle of the cut is larger so they can get more tooth contact. they may have made the pinion smaller, but have maintained as much contact area as possible.
lwb 1.6efi,4sp auto,f&r airlockers,dual t/cases.custom coils.builder of ROAD LEGAL custom suzukis...and other stuff.
CAD modelling-TECH drawings-DXF preparation.
http://www.auszookers.com/index.php
CAD modelling-TECH drawings-DXF preparation.
http://www.auszookers.com/index.php
Just in case anyone wants to work out the thrust - here's some links to TIMKENS gear thrust data...
index of terms : http://pdf.directindustry.com/pdf/timke ... -_19.html#
Hypoid Formula : http://pdf.directindustry.com/pdf/timke ... 9-_21.html
Gave me a headache so I'll leave it to the numerically inclined.
index of terms : http://pdf.directindustry.com/pdf/timke ... -_19.html#
Hypoid Formula : http://pdf.directindustry.com/pdf/timke ... 9-_21.html
Gave me a headache so I'll leave it to the numerically inclined.
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
back to the question, it will be numming at 4300 rmp @ 1ookmh. bit too high for my likings.and while the 4.6 will be running at 3800rpm @100kmh, good luck finding 2 front centres a wrecker. be cheaper to buy transfer gears
jason
jason
WANTED: swb vitara rear seat. the 3 seater bench type
for sale: wt diffs, snake hi steer, maruti 4.1 wt centres,
for sale: wt diffs, snake hi steer, maruti 4.1 wt centres,
how are you working out your rpm? i'm getting 4310rpm for .865 5th gear, 1.45 wt transfer, 5.12 diff 31'' tyre @ 62mph
http://www.rocky-road.com/calculator.html
jason
http://www.rocky-road.com/calculator.html
jason
WANTED: swb vitara rear seat. the 3 seater bench type
for sale: wt diffs, snake hi steer, maruti 4.1 wt centres,
for sale: wt diffs, snake hi steer, maruti 4.1 wt centres,
Who is online
Users browsing this forum: No registered users and 0 guests