i my 60 series winch truck it was setup so that when you engaged the aie locker it also pressuried the diffs to stop water getting in do you think i should redo it this way or just put diff breathers ?
cheers
nathan
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
pressurised diffs
Moderators: toaddog, TWISTY, V8Patrol, Moderators
Re: pressurised diffs
surely 100psi would be pushing oil out of the seals? I'd just run decent breathers...tuff6ty wrote:i my 60 series winch truck it was setup so that when you engaged the aie locker it also pressuried the diffs to stop water getting in do you think i should redo it this way or just put diff breathers ?
cheers
nathan
Re: pressurised diffs
what he saiddogbreath_48 wrote:surely 100psi would be pushing oil out of the seals? I'd just run decent breathers...tuff6ty wrote:i my 60 series winch truck it was setup so that when you engaged the aie locker it also pressuried the diffs to stop water getting in do you think i should redo it this way or just put diff breathers ?
cheers
nathan
youd still need some sort of diff breathers ideally, when they heat up the air needs to have somewhere to go.
If you pressurised them you'd need to keep the pressure low like the guys above suggested, you probably aren't going to drive through any more than 1.2 metres of water so if my calcs are correct the water would exert about 1.7psi on the seals (thats assuming that the water is 1200mm above the seals and isn't being forced into them) so yea any mor than 2-3psi may cause trouble.
If you're gonna set up 2-3psi plumb it to the gearbox, transfer and dizzy while you're at it, just don't blame me when you keep finding puddles of oil under the car....
Pretty sure military spec hummers had a similar set up, they could park fully submerged...
If it was my car tho i'd just extend all the breathers up high, not drive through water unless i have to, check all oils after water crosssing, you'll soon get to know which bits water gets into.
e.g. in my old MQ i drove through water over the bonnet a few times (wonnangatta at a high level) and got water in the front diff, and bottom of aircleaner cyclone but never anywheres else.
If you pressurised them you'd need to keep the pressure low like the guys above suggested, you probably aren't going to drive through any more than 1.2 metres of water so if my calcs are correct the water would exert about 1.7psi on the seals (thats assuming that the water is 1200mm above the seals and isn't being forced into them) so yea any mor than 2-3psi may cause trouble.
If you're gonna set up 2-3psi plumb it to the gearbox, transfer and dizzy while you're at it, just don't blame me when you keep finding puddles of oil under the car....
Pretty sure military spec hummers had a similar set up, they could park fully submerged...
If it was my car tho i'd just extend all the breathers up high, not drive through water unless i have to, check all oils after water crosssing, you'll soon get to know which bits water gets into.
e.g. in my old MQ i drove through water over the bonnet a few times (wonnangatta at a high level) and got water in the front diff, and bottom of aircleaner cyclone but never anywheres else.
There are no stupid questions, but there are a LOT of inquisitive idiots
unimogs have pressurised diff, bellhousing, gearbox and headlights.
from memory the pressure is 2-3 psi. no problem with oil leaks and no problem with water inside any pressurised unit. they use a pressure reducer but again can't remember what brand. easier way is just to add extended breathers.
from memory the pressure is 2-3 psi. no problem with oil leaks and no problem with water inside any pressurised unit. they use a pressure reducer but again can't remember what brand. easier way is just to add extended breathers.
MUD, MUD, GLORIOUS MUD!
Funny contrast. Here I am running my engine crank case at 5psi of Vacuum.
I wouldn't bother with the pressurising, it will be fairly difficult to regulate and should something get blocked you may have oil pouring out everywhere.
I suppose it depends on how often you submerge your car, and how long for each time. Most water crossing's i've been through have never been more than 10seconds or so.
If you intend to drive up a river... it may be a different story.
I wouldn't bother with the pressurising, it will be fairly difficult to regulate and should something get blocked you may have oil pouring out everywhere.
I suppose it depends on how often you submerge your car, and how long for each time. Most water crossing's i've been through have never been more than 10seconds or so.
If you intend to drive up a river... it may be a different story.
Stirling
1981 Series 3 Stage 1 Land Rover - 3.5L LPG V8 - 12:1CR - 6 35W HID Lights
2" Lift, 33"x12.5" Baja Claws & MaxiDrive front Locker
Videos:
http://www.youtube.com/user/stirlsilver
1981 Series 3 Stage 1 Land Rover - 3.5L LPG V8 - 12:1CR - 6 35W HID Lights
2" Lift, 33"x12.5" Baja Claws & MaxiDrive front Locker
Videos:
http://www.youtube.com/user/stirlsilver
Who is online
Users browsing this forum: No registered users and 1 guest