Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

removing warning light toyota

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 283
Joined: Fri May 20, 2005 1:55 pm
Location: maitland

removing warning light toyota

Post by matto »

My mates got a land cruiser 100 series and his dash always shows a timming belt warning light how do you remove this?
nissan 98 gu 5" lift 37 creepys, 80%reduction gears, front locker and a gen3 and no money.
Top
Posts: 3224
Joined: Mon Jan 12, 2004 6:03 pm
Location: Moggill

Post by phippsy »

Behind the clear dash cover there will be a small button to press, has he replaced the timing belt though??
Top
Posts: 283
Joined: Fri May 20, 2005 1:55 pm
Location: maitland

Post by matto »

he would have had it done. Can you see the button with the dash in? where abouts?
nissan 98 gu 5" lift 37 creepys, 80%reduction gears, front locker and a gen3 and no money.
Top
Posts: 3224
Joined: Mon Jan 12, 2004 6:03 pm
Location: Moggill

Post by phippsy »

Somewhere on the instrument cluster, there might be a small rubber grommet to move then a pin or something like that to reset it.
Top
Posts: 5179
Joined: Fri Dec 05, 2003 8:15 pm
Location: Brisbane Australia

Post by Shadow »

phippsy wrote:Somewhere on the instrument cluster, there might be a small rubber grommet to move then a pin or something like that to reset it.
i thionk its done with an ignition combination on the 100series

ie, gotta go through a routine, like switch car on, then off for 5 seconds, then on, select D etc
Top
Posts: 579
Joined: Mon May 29, 2006 4:36 pm
Location: Melbourne

Post by bigcam »

with ignition turned on, using the trip switch , change the display to ODO, and then turn the ignition OFF
While pressing the trip switch,turn the ignition switch ON and hold for five seconds
Release the trip switch,then press the switch again within five seconds.The digital display should change to T- BELT MODE. Each press of the switch then should change the reset time by 10,000km increments. After setting the klms hold the trip switch ON for more than five seconds then release the switch. Check that the display has now changed back to ODO and that now the warning has gone off when the engine is started
[quote="75 cruser"]we want more donkey[/quote]
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Post by want33s »

:armsup: AWESOME stuff Cam.
Good to see clear concise info being shared around..
I'll keep a copy of that for the day I get a 100 series.. Buggered if I know when that'll be but one day. :cry:
Top
Posts: 579
Joined: Mon May 29, 2006 4:36 pm
Location: Melbourne

Post by bigcam »

cant take credit.. it came from google.. but hey if i can find it and someone else can't then sharing is good!
[quote="75 cruser"]we want more donkey[/quote]
Top
Posts: 17
Joined: Sat Jun 07, 2008 8:12 pm
Location: brisbane

Post by luxman278 »

any one know how to do the same to a 3litre diesel hilux.
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 1 guest