Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

gq rhf tyre rubbing on control arm! WHY??

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Forum rules
Post Reply
Posts: 18
Joined: Sat Aug 18, 2007 12:25 pm
Location: Jimboomba

gq rhf tyre rubbing on control arm! WHY??

Post by mq308lwb »

I have a gq wagon with 3" spring lift, 2" body and the castor bushes installed But i still have a problem with my rhf tyre rubbing on the rhf control arm.

I am a bit pusled by this as at full left lock there is no scrubbing but not even at full right lock the rhf tyre is scrubbing..


Any suggestions, could it be that when the last wheel alignment was done that the steering was not centred and then adjusted or are there other things that could be causing this??

Thanks for your help...
Top
Posts: 4275
Joined: Thu Dec 19, 2002 2:12 pm
Location: Sydney

Post by ozy1 »

could just be that your steering stops have been incorrectly adjusted, or the most common thing is that you bent the right hand steering stop on a pervious outing, have a look at the bolt on the right hand swivel hub that acts as your steering stop
Top
Posts: 252
Joined: Fri Sep 02, 2005 3:45 pm
Location: outside your window

Post by hiy6o »

Sounds like the steering stops to me too , Just check you haven't bent the radius arm though , had this happen to me , didn't think you could bend cast iron that far without it breaking , but I have the new arm to prove it. :roll:
Nup not telling
you'll have to find out yourself
Top
Posts: 248
Joined: Tue Mar 30, 2004 3:44 pm
Location: Sydney Australia

Post by zuffen »

I would have thought the 3" lift altered the effective length of the drag link which gives more stering one way than the other.
Cheers,

Zuffen

There's no such a thing as too much horsepower
Top
Posts: 4275
Joined: Thu Dec 19, 2002 2:12 pm
Location: Sydney

Post by ozy1 »

zuffen wrote:I would have thought the 3" lift altered the effective length of the drag link which gives more stering one way than the other.
could be the case but lifting a truck i think reduces the turning circle so you would have less chance of rubbing, i still say steering stops
Top
Posts: 34
Joined: Wed May 28, 2008 4:25 pm
Location: Perth W.A

Post by GQ4X4 »

Check ya radius arm...i had the same prob except mine was the lhf...turned out ot be a bent radius arm...ill dig up a photo of it..
Top
Posts: 709
Joined: Thu Sep 22, 2005 7:49 pm
Location: campbelltown

Post by Mousie »

mine dose this with the large size tyres.
R.A.G, Ruff As Gutts 4x4 club :P
http://www.rag4x4.com/
Top
Posts: 21
Joined: Sat Feb 23, 2008 11:54 am
Location: LILYDALE

Post by Snappa_Patrolapart »

do u have an ajustable panhard if you do make it .... shorten it a few turns
Top
Posts: 709
Joined: Thu Sep 22, 2005 7:49 pm
Location: campbelltown

Post by Mousie »

yeh i do and i have got it centred and it scrubs both sides..

cheers
R.A.G, Ruff As Gutts 4x4 club :P
http://www.rag4x4.com/
Top
Posts: 965
Joined: Fri Mar 26, 2004 10:09 am
Location: B.F.E

Contact:
Contact RMP&O

Post by RMP&O »

I just finished repairing a busted steering stop bolt causing this exact same problem. Had to tear it all down and pull knuckle. Then drill it in press....replaced with grade 10.8 metric.

Was pretty dirty so cleaned it all and repacked it too! Knuckle stubs on axle end not real smooth so polished them up while at it. Much better now! :armsup:
www.rmp-o.com
Top
Posts: 75
Joined: Tue May 23, 2006 1:19 pm
Location: brisbane

Post by evo wagon »

mine rubs when i turn right full lock although i have 39's which are 18inchs wide lol doesnt do it when i turn left though ah well
Top
Post Reply

Return to “Nissan”

Who is online

Users browsing this forum: No registered users and 21 guests