Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Removing 3rd member bolts from housing

Tech Talk for Rover owners.

Moderator: Micka

Forum rules
Post Reply
Posts: 1614
Joined: Fri Feb 21, 2003 8:44 pm
Location: Melbourne

Removing 3rd member bolts from housing

Post by landy_man »

How do you remove the round headed bolts in the axle housing... hammer ?? or grinder ?? :?
Top
Posts: 10984
Joined: Thu May 29, 2003 3:47 pm
Location: Bum drilling with my buddy Ray!

Post by GRIMACE »

TNT :lol:
Top
Posts: 200
Joined: Wed Dec 04, 2002 1:11 am
Location: Perth WA

Post by discokid »

Use a hammer and bang them into the housing
Top
Posts: 510
Joined: Tue Jul 22, 2003 9:42 pm
Location: melbourne

Post by modman »

if they are push in studs then do as diuscokid says, if they screw in then lock 2 nuts together and screw out.
sounds like hilux 3rd'sgoing in ???????
if so, please post the process.

modman ;)
Top
Posts: 1614
Joined: Fri Feb 21, 2003 8:44 pm
Location: Melbourne

Post by landy_man »

hilux 3rd is definately going in...Just waiting for Jac Mac to open to get axles.. and need to find someone to machine stubs

can't wait to get it on the road again.. the new ratios are also going to make a huge difference I reckon...

did not think about the 2 nut trick...
will keep posted on progress...
Top
Posts: 510
Joined: Tue Jul 22, 2003 9:42 pm
Location: melbourne

Post by modman »

does jmac charge too much to machine thestubs and press a bronze bush in?

modman :?:
Top
Posts: 1614
Joined: Fri Feb 21, 2003 8:44 pm
Location: Melbourne

Post by landy_man »

would not have a clue...have not spoken to them, as I only started on Friday and they are closed for the break.... a mate has a lathe so we will see how we go... but it might just be easier to send them the stubs
Top
Posts: 510
Joined: Tue Jul 22, 2003 9:42 pm
Location: melbourne

Post by modman »

i think he charges $180 to machine out both stubs
the bronze bushes cost $30 each
hope this helps??

modman ;)
Top
Posts: 1614
Joined: Fri Feb 21, 2003 8:44 pm
Location: Melbourne

Post by landy_man »

Thanks...$180 sounds expensive ..It could not possibly take them say an hour @ $90( :shock: ) to take off 20 thou

Do you know when they re-open ?
Top
Posts: 104
Joined: Mon Sep 08, 2003 10:50 pm
Location: left of center

Post by tiggr »

mmmmm "Presedent of the no jap crap club " putting JAP CRAP into his Rangie .....a little ironic i thunk !
:rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl:
discourage inbreeding , ban country music ! Rover didn't make computers as they just couldn't find a way for them to leak oil .
Top
Posts: 1614
Joined: Fri Feb 21, 2003 8:44 pm
Location: Melbourne

Post by landy_man »

tiggr wrote:mmmmm "Presedent of the no jap crap club " putting JAP CRAP into his Rangie .....a little ironic i thunk !
:rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl: :rofl:


thats Mr President to you........ :rofl: :rofl: :rofl: :rofl: :rofl: :rofl:
Top
Posts: 510
Joined: Tue Jul 22, 2003 9:42 pm
Location: melbourne

Post by modman »

no idea when they open.
those prices were quoted when i enquired about the whole toy 3rd. conversion front and rear.
you have bought stuff, it may bring the price down.


modman ;)
Top
Post Reply

Return to “Rover”

Who is online

Users browsing this forum: No registered users and 0 guests