i want to replace the pipe thats gose from gear box to transfercase on my hj60 83 modle,
alsowheel studs and nut cheapest around melbourne?
also second problem after chaning my disc pad on the front i have found a rather crap sheared bolt thats holds the brake calibar on i found the thread on the housing itself cross threaded any idead how to fix seen as my drill only gose to 13mm and im not will to compremise on saftey it has to be safe or not
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
where to get a pipe
Moderators: toaddog, Elmo, DUDELUX
where to get a pipe
1995 land rover disco on 265 muddies
for all these i'd just head to a local wreckers for the studs and stuff.
the pipe will be after market.
alot of people put the balance pipe in as some times the seal between the transfer and the gear box weeeps and they drain one into the other and the you dry seize the box so add a pipe to allow the oil to flow freely between the two.
for the cross threaded hole i would see if you can strip the knuckle down so you can run a tap from the opposite side back.
so in turn you should be able to pick up the original thread run it through then hit the cross section and clean that out aswell
the pipe will be after market.
alot of people put the balance pipe in as some times the seal between the transfer and the gear box weeeps and they drain one into the other and the you dry seize the box so add a pipe to allow the oil to flow freely between the two.
for the cross threaded hole i would see if you can strip the knuckle down so you can run a tap from the opposite side back.
so in turn you should be able to pick up the original thread run it through then hit the cross section and clean that out aswell
Re: where to get a pipe
ebay for the pipe ( or enzed or pirtec will make you one quicksmart)matthewK wrote:i want to replace the pipe thats gose from gear box to transfercase on my hj60 83 modle,
alsowheel studs and nut cheapest around melbourne?
also second problem after chaning my disc pad on the front i have found a rather crap sheared bolt thats holds the brake calibar on i found the thread on the housing itself cross threaded any idead how to fix seen as my drill only gose to 13mm and im not will to compremise on saftey it has to be safe or not
as for teh bolt, strip the hub, and buy the corresponding recoil kit and recoil the thread, it will be better than before.
Jes
ATTACH BROKEN TOYOTA HERE--->
DUCATI <-----Worlds best warning label
DUCATI <-----Worlds best warning label
just down from southern arb in dandy
The wheel studs and nuts are only about 8 bucks each from and spares place.
I replace 5 of mine last weekend and they only cost me 25 bucks for all on trade price.
I replace 5 of mine last weekend and they only cost me 25 bucks for all on trade price.
Current ride,
96 GQII TD42
Previous rides,
87 High Lux single cab. Yes she was my first!
93 80 series Land Cruiser.
Project Zook Vitara. Previously rolled! So I just had to get the 9 inch out!
96 GQII TD42
Previous rides,
87 High Lux single cab. Yes she was my first!
93 80 series Land Cruiser.
Project Zook Vitara. Previously rolled! So I just had to get the 9 inch out!
Who is online
Users browsing this forum: No registered users and 8 guests