Any Photos of hydraulic bump stop cans welded in so that I can get an idea on how to mount them properly. Thanks. Much appreciated.
LudaCris
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Any Photos of hydraulic bump stop cans welded in.
Moderators: toaddog, TWISTY, V8Patrol, Moderators
Any Photos of hydraulic bump stop cans welded in.
Cris's 4 X 4 Accessories & Suspension 0404 736 325 Rock Sliders From $499
Few pics on the following links. The consensus seems to be to weld a bracket to the can and then weld to chassis as in this picture below.
http://pirate4x4.com/forum/showthread.p ... bump+stops
http://pirate4x4.com/forum/showthread.p ... bump+stops
http://pirate4x4.com/forum/showthread.p ... bump+stops
http://pirate4x4.com/forum/showthread.p ... bump+stops
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Go on www.race-dezert.com/forum dezert racer site but everyone runs them plenty of pics.
Didn't even know they existed 
Hijack - What bump stop would be best on a leaf sprung hilux that has:
Rears up front / leafs removed / extended shackles
(so pretty flexi)
Looking at ordering from:
http://www.suspension.com/Bumpstop.htm
Was going to go the 80series bumpstops but they want $80 each at the wreckers and i reckon it would be cheaper to get these american ones which are new
Hijack - What bump stop would be best on a leaf sprung hilux that has:
Rears up front / leafs removed / extended shackles
(so pretty flexi)Looking at ordering from:
http://www.suspension.com/Bumpstop.htm
Was going to go the 80series bumpstops but they want $80 each at the wreckers and i reckon it would be cheaper to get these american ones which are new
Kind Regards,
Brad
Brad
Have just put a set of King 2.5's in the GQ race rig, still have some gusseting to do but they work good!
It's not a easy job! take ya time, coz if you put them in wrong you can bind them up on the spring. And also use the coldest welder you can get ya hands on as the tubes (cans) are made from Cro-Mo and if you put to much heat on them it will 'blister' inside and you wont be able to get the bumpstop back in, unless you have a course stone hone and even if so be prepared for at least a 1/2 hr of honing as the stuff is tuff!
There a bit freaky to drive with as they bang a bit when they hit the contact surface on the top of the diff, And also you can pump them up to 300psi with Nitrogen, OH Important!......If you can try not to get them already pumped up, as they will be a nightmare to fit as the total lenth of them when pumped up is 19 inches!
Will put some pics up if you need them
Steve.
It's not a easy job! take ya time, coz if you put them in wrong you can bind them up on the spring. And also use the coldest welder you can get ya hands on as the tubes (cans) are made from Cro-Mo and if you put to much heat on them it will 'blister' inside and you wont be able to get the bumpstop back in, unless you have a course stone hone and even if so be prepared for at least a 1/2 hr of honing as the stuff is tuff!
There a bit freaky to drive with as they bang a bit when they hit the contact surface on the top of the diff, And also you can pump them up to 300psi with Nitrogen, OH Important!......If you can try not to get them already pumped up, as they will be a nightmare to fit as the total lenth of them when pumped up is 19 inches!
Will put some pics up if you need them
Steve.
GQ Space Cab V8. Team Toxic, Sponsored by Dobinsons Suspension Sydney 02 4647 8295 Loveday 4x4 Adventures, Sharmans Engineering, Lightforce, R&B Tiling Services, CW Crash and my long suffering wife.
remember they are bumpstops. I have seen them set up as shocks half way through the travel which make tuning of bypass shocks very hard. They should only touch on BIG wash outs / massive jumps etc. some vids like wasteland warriors show them working and they contact about 3 times in 5 mins desert racing. As for mounting I have seen a few inside the chassis rail (ie holesawed from above rail right through cutting chassis in 2 then using the can to hold the chassis together.) as there are space problems on trucks. Brace it very well or it will fail if cutting the chassis through.
cheers bru
cheers bru
ADHD Racing would like to thank
Mrs Bru @ Sunshine Coast Developmental Physiotherapy - www.scdphysio.com.au , Ryano @ Fourbys www.generaltire.com.au Blitzkrieg Motorsport
Mrs Bru @ Sunshine Coast Developmental Physiotherapy - www.scdphysio.com.au , Ryano @ Fourbys www.generaltire.com.au Blitzkrieg Motorsport
remember they are bumpstops. I have seen them set up as shocks half way through the travel which make tuning of bypass shocks very hard.
What you might be seeing there is for some restricted classes allow bumps but have to retain factory sway bars. So they mount the bumps low to help out the sway bar reduce body roll.
What you might be seeing there is for some restricted classes allow bumps but have to retain factory sway bars. So they mount the bumps low to help out the sway bar reduce body roll.
http://www.dirtcomp.com.au/
It also has to do alot with the 'bind lenth' of your springs.
Is no use having a bumpstop set to high that it allows the spring to bind before all the effectivness of the bumpstop is achieved, the whole idea of it is to take some of the shock load out of the front end, you will not hurt them as that is what they are designed to do.
Had a heap of help from James here in S.A. ( the off-road shop) in getting the set-up right, he is a buggy bloke.
Steve.
Is no use having a bumpstop set to high that it allows the spring to bind before all the effectivness of the bumpstop is achieved, the whole idea of it is to take some of the shock load out of the front end, you will not hurt them as that is what they are designed to do.
Had a heap of help from James here in S.A. ( the off-road shop) in getting the set-up right, he is a buggy bloke.
Steve.
GQ Space Cab V8. Team Toxic, Sponsored by Dobinsons Suspension Sydney 02 4647 8295 Loveday 4x4 Adventures, Sharmans Engineering, Lightforce, R&B Tiling Services, CW Crash and my long suffering wife.
heres a couple of pics of how me and my navi set mine up.
I have a 4" lift so we slid everything up 2", that way if i ever want to lower the spring height all i have to do is cut off the striker plate and make a slimmer one.
If you can get one use a tig to weld the gussets to the cans as i spent 5 hours honing mine out
Also i took the rubber bump stops off the back and welded them under the chassis rail. when i set up the stricker plate i allowed for 20mm compression of the rubber so as not to bottom out the hyd bump stops.
cheers smitty
I have a 4" lift so we slid everything up 2", that way if i ever want to lower the spring height all i have to do is cut off the striker plate and make a slimmer one.
If you can get one use a tig to weld the gussets to the cans as i spent 5 hours honing mine out
Also i took the rubber bump stops off the back and welded them under the chassis rail. when i set up the stricker plate i allowed for 20mm compression of the rubber so as not to bottom out the hyd bump stops.
cheers smitty
innovation is better, better is faster, and fast is all that counts
Here's another idea for ya hammey, the missus came up with it!
Now you have finished run a bit os sillicone around the base of the can where it meets the bumpstop as well as up the top where the allen key bolt sticks out on the one side ( as well as the secondary holein the top) as this will stop the ingress of grit which will jam the bumpstop in there if you ever need to get it out!
Thought it was a great idea, stops them gettin jammed on from dirt being inside!.....she's a clever little girl!
Steve.
Now you have finished run a bit os sillicone around the base of the can where it meets the bumpstop as well as up the top where the allen key bolt sticks out on the one side ( as well as the secondary holein the top) as this will stop the ingress of grit which will jam the bumpstop in there if you ever need to get it out!
Thought it was a great idea, stops them gettin jammed on from dirt being inside!.....she's a clever little girl!
Steve.
GQ Space Cab V8. Team Toxic, Sponsored by Dobinsons Suspension Sydney 02 4647 8295 Loveday 4x4 Adventures, Sharmans Engineering, Lightforce, R&B Tiling Services, CW Crash and my long suffering wife.
Who is online
Users browsing this forum: No registered users and 2 guests