Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

ARB BULLBAR MOD

Tech Talk for Rover owners.

Moderator: Micka

Forum rules
Post Reply
Posts: 12
Joined: Tue Sep 25, 2007 11:54 pm
Location: narre

ARB BULLBAR MOD

Post by forget »

g,day all
i have a range rover 1990 with a standard non winch arb bullbar
i am wanting to put a winch into this bar spoke to some wanker at arb and he says the bar will not fit a winch and that i need to buy a winch bar
is there a way that i can cut and weld in a winch plate to mount a winch into this bar or has any one done this before
or maybe someone knows where i could get this modification done in the dandenong/cranbourne area
all help appreciated
thanks again
shane
Top
Posts: 181
Joined: Sun Aug 22, 2004 4:37 pm
Location: melbourne

Contact:
Contact swamp

Post by swamp »

The bars are the same and the winch bar has provisions ie pevetrations and bolt holes for the winch
It depends on how handy you are with a welder and grinder and time verses money .
Smithies outback in Cranbourne should be able to look after it if you want to farm it out.
REgards
Michael.
out of my mind, back soon.
Top
Posts: 400
Joined: Thu Jun 24, 2004 8:56 pm
Location: Wakerley, Brisbane

Post by 86MUD »

Yes...I have done it.

The original "non-winch" bar did need in a lot of additional welding on joints to add strength. I also trimmed the corners and added side bars to protect the panel a bit more and improve approach angle. Spent about 6 huors on it!

Image

cheers
Andrew
Top
Posts: 1005
Joined: Sat Aug 02, 2003 8:34 am
Location: Croydon, Victoria

Post by TRobbo »

It certainly can be done and Cheezy racing in Bayswater has also done it.

I was of the understanding that the centre plate sections in the non winch bar was not as thick as the winch bar model. Perhaps this was only applicable on the older bars.
Warn - Dont leave home without it
Top
Posts: 59
Joined: Sat Nov 11, 2006 9:17 am
Location: Melbourne, Victoria

Contact:
Contact dassaw

Post by dassaw »

I also did it with my arb bar, just made a cradle out of 3mm plate to fit in between the rails of the bullbar.

There was a write up on AULRO, thats what I used, so just have a search on there for bullbar cradle or tjm cradle, as it was a tjm bar he did it for.

cheers
'97 300tdi Discovery, Fr & R Air lockers
35" Silverstones
www.blackrangeoffroad.com.au
Top
Posts: 19
Joined: Thu May 20, 2004 9:11 am
Location: Vic.

Post by Blue Rangie »

:lol: Then you could always buy a good second hand one from me to suit a Disco with crush tubes.
Mike
Mike Smith
Top
Posts: 56
Joined: Thu Jun 19, 2008 10:12 pm
Location: woolgoolga NSW

Post by TimRover »

Blue Rangie wrote::lol: Then you could always buy a good second hand one from me to suit a Disco with crush tubes.
Mike
Should i ask how much??
Top
Posts: 12
Joined: Tue Sep 25, 2007 11:54 pm
Location: narre

Post by forget »

Blue Rangie wrote::lol: Then you could always buy a good second hand one from me to suit a Disco with crush tubes.
Mike
cool mate but what are crush tubes
i was looking for this type of bar

http://www.roverparts.com/Parts/9402ARB.cfm
thanks
Top
Post Reply

Return to “Rover”

Who is online

Users browsing this forum: No registered users and 0 guests