Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

cross member mods

Tech Talk for Rover owners.

Moderator: Micka

Forum rules
Post Reply
Posts: 28
Joined: Wed Dec 20, 2006 12:30 pm
Location: cowwarr

cross member mods

Post by roverbeau »

gday just wondering what people have done to modify the cross member. i am fitting a t700 with lt95 to my rangi but the front shaft hits the cross member. could i cut out a section and weld in a half cut piece of pipe in there and would that be strong enough.
thanks.
beau
Top
Posts: 56
Joined: Sun Aug 05, 2007 12:56 pm
Location: sydney

Post by advdisco1 »

thats what i did, with a 200mmish piece of 6mm steel cut to shape and welded(on edge) to the underside of the cutout. don't think its as strong
as the original so i welded another piece of 12mm solid rod on the inside
of the cutout to help it from collapsing.
Top
Posts: 28
Joined: Wed Dec 20, 2006 12:30 pm
Location: cowwarr

Post by roverbeau »

thats what i was thinkin of doing. i dont know how strong the standard one is any way. my truck is all smashed up under there and there isnt to much straight bits left
Top
Posts: 28
Joined: Wed Dec 20, 2006 12:30 pm
Location: cowwarr

Post by roverbeau »

thats what i was thinkin of doing. i dont know how strong the standard one is any way. my truck is all smashed up under there and there isnt to much straight bits left
Top
Posts: 3064
Joined: Sun Jun 12, 2005 11:00 pm
Location: Yinnar South, Vic

Contact:
Contact cloughy

Post by cloughy »

My rangie tray, I never had one at all

And on my Diesel one, I've done this to clear the 3" exhaust

http://www.aulro.com/afvb/isuzu-landy-e ... post772966
Wanted: Car trailer or beaver tail truck, let me know what you got
Top
DL
Posts: 299
Joined: Wed May 31, 2006 8:33 pm
Location: Bellarine, Brackistan

Post by DL »

Didn't some later models have a crossmember made out of 2" tube? Have one lying around here somewhere.
Top
Posts: 1175
Joined: Wed Jul 27, 2005 10:17 pm
Location: Mirboo North

Post by 6.5 rangie »

It didn't need a crossmember mod when it was in my car, so can't see how its hitting it. Oh and i have your dipstick, will give it to Matt tomorrow.
Damien


--------------------------------------------------------
Top
Posts: 28
Joined: Wed Dec 20, 2006 12:30 pm
Location: cowwarr

Post by roverbeau »

Thanks for that mate. It mounts an inch back in my ute i think because the mounts were out and i had to redrill the holes. But its all in now just gotta make the floor to fill the big hole and mount the shifter. I just cut a section out of the cross member.
thanks again
Top
Posts: 1175
Joined: Wed Jul 27, 2005 10:17 pm
Location: Mirboo North

Post by 6.5 rangie »

roverbeau wrote:Thanks for that mate. It mounts an inch back in my ute i think because the mounts were out and i had to redrill the holes. But its all in now just gotta make the floor to fill the big hole and mount the shifter. I just cut a section out of the cross member.
thanks again
Oops :roll: , i forgot about that, i modded those mounts when i set that box up in my old 110 extra cab (that Matt now has) with the gen3 in it, i moved it back around 50mm so the sump would clear the drag link, so thats why they where out. Sorry
Damien


--------------------------------------------------------
Top
Posts: 28
Joined: Wed Dec 20, 2006 12:30 pm
Location: cowwarr

Post by roverbeau »

no worries mate, its all going now. all i have 2 do is mount the shifter and make a high low lever that will hang out the floor and thats it.
thanks 4 bringing down the dip stick to
Beau
Top
Post Reply

Return to “Rover”

Who is online

Users browsing this forum: No registered users and 28 guests