hey guys
just found a oil leak in my zook it look like it is coming from the rear main seal what it the easy way to change it??
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
oil leak
1) get a copy of the factory service manual.
2) buy a replacement rear main seal.
3) follow the instructions in the service manual.
Seriously, you have to pull the gearbox, clutch and flywheel. You'll need to get the torque settings right on everything and you'll need a clutch alignment tool.
It's not a 5 minute job and there's no "quick" way of doing it, only the right way.
Steve.
2) buy a replacement rear main seal.
3) follow the instructions in the service manual.
Seriously, you have to pull the gearbox, clutch and flywheel. You'll need to get the torque settings right on everything and you'll need a clutch alignment tool.
It's not a 5 minute job and there's no "quick" way of doing it, only the right way.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
x 2. You could probably get by without the clutch alignment tool, but it does make life easier. If you don't align your clutch friction disc back up properly, the gearbox won't back in no matter how hard you try.Gwagensteve wrote:1) get a copy of the factory service manual.
2) buy a replacement rear main seal.
3) follow the instructions in the service manual.
Seriously, you have to pull the gearbox, clutch and flywheel. You'll need to get the torque settings right on everything and you'll need a clutch alignment tool.
It's not a 5 minute job and there's no "quick" way of doing it, only the right way.
Steve.
i would pull motor and box out together loosly tighten clutch bolts slide together then once aligned pull apart and tighten. a bit fiddly but does the job. also check gearbox seal while there apart i made the mistake of only doing the rearmain and found out my gearbox seal was rooted too. pull it all out do it again yay
I jotted down a list of things i learnt when i replaced my clutch. (which covers 99% of what your going to experience. Its in the bible somewhere "How to...."
If i new that before i started it would have been alot easier....eg jamming a screwdriver into the flywheel to torque up the clutch housing. I didnt use a alignment tool, makes it more fiddly but easily possible still. Goodluck.
If i new that before i started it would have been alot easier....eg jamming a screwdriver into the flywheel to torque up the clutch housing. I didnt use a alignment tool, makes it more fiddly but easily possible still. Goodluck.
- Exciting stock 96 Coily Sierra...
- Custom Roll Bar
- Diff breathers
30/31's to come...
- Custom Roll Bar
- Diff breathers
30/31's to come...
thank mate ill let you all know how it goesda13ro wrote:I jotted down a list of things i learnt when i replaced my clutch. (which covers 99% of what your going to experience. Its in the bible somewhere "How to...."
If i new that before i started it would have been alot easier....eg jamming a screwdriver into the flywheel to torque up the clutch housing. I didnt use a alignment tool, makes it more fiddly but easily possible still. Goodluck.
and thanks again with all the help
Who is online
Users browsing this forum: No registered users and 68 guests