Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

1.3 plug lead resistance?

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Forum rules
Post Reply
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

1.3 plug lead resistance?

Post by want33s »

Anyone know what the plug lead resistance is supposed to be? It's not mentioned in the FSM :cry:

Thanks,
Jas
Top
Posts: 4760
Joined: Mon Dec 30, 2002 6:04 am
Location: Adelaide

Contact:
Contact murcod

Post by murcod »

If you're trying to diagnose a fault then in my experience using a multimeter to check is a pointless exercise. The lead might measure OK but be breaking down with high voltage.
David
Top
Posts: 3098
Joined: Sat May 28, 2005 3:22 pm
Location: Melbourne, Australia

Post by PJ.zook »

As murcod says, you still can be getting a good reading, but only in the extremely low current flow from a multimeter.
Best thing to do, is to buy new leads to eliminate them out of youre fault tracing. If it didnt work, then youre old leads are propably still good, so keep them as spares.
Motorized three seater couch buildup:

http://www.outerlimits4x4.com/viewtopic ... 0&t=196047
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Post by want33s »

Just trying to sort a niggly problem.
The other day it conked out with no warning and rolled to a stop in gear. I checked coil leads and rotor and then it started.
Had an intermittent miss for the rest of the day which wasn't bad enough to stop me but on the way home it died 3 or 4 times. Had to pull over on highway.
It restarted first hit of the key without even opening the bonnet.
I tested the coil resistance and it appears fine, put it in another car and it doesn't show the miss.

So next guess was a cracked or shorted coil lead.
I just went and bought a set of Bosch leads and plugs (which it probably needed anyway), so I'll fit them in the morning and see what happens.

Jas.
Top
Posts: 179
Joined: Sat Jun 14, 2008 9:43 pm
Location: Shidney

Post by RockHopper »

From memory, I think the rule of thumb was no greater than 14k ohm per 30 cm's of lead. You're problem to me sounds like the ignition module may be on it's way out. Some model cars tacho's play up when the module is on the way out. I don't know if the Sierra falls into this category, but the old Magna's, Camira's and Telstars were renoun for it.
Last edited by RockHopper on Fri Dec 12, 2008 6:20 am, edited 1 time in total.
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Post by want33s »

RockHopper wrote:From memory, I think the rule of thumb was no greater than 40k ohm per 30 cm's of lead. You're problem to me sounds like the ignition module may be on it's way out. Some model cars tacho's play up when the module is on the way out. I don't know if the Sierra falls into this category, but the old Magna's, Camira's and Telstars were renoun for it.
You may have something there... The tacho was bouncing around a bit while it was spluttering.
I'll have to carry a spare.

Jas.
Top
Posts: 2297
Joined: Mon Mar 06, 2006 1:23 pm
Location: Melbourne-Australia

Post by MightyMouse »

Just remember that inductive leads are different to resistive leads ( which really are obsolete technology - and failure prone ).

If your replacing .... inductive are a much beter option,
( usual disclaimers )

It seemed like a much better idea when I started it than it does now.
Top
Post Reply

Return to “Suzuki”

Who is online

Users browsing this forum: No registered users and 1 guest