Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

front wheel leaning over?? uni's DIY?

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 48
Joined: Thu Jan 17, 2008 4:41 pm
Location: South Brisbane

front wheel leaning over?? uni's DIY?

Post by zero »

Went wheeling up north along the beach near double island point for a few days, nothing
too hardcore mostly just sand, there was a lot of rough corrugated parts though.


anyways coming home noticed the front passenger wheel was leaning way over at the top.
knowing nothing about solid axles or the ball joints? i dont even know where to start at
straightening this up.


havent really had a chance to have a good look but any advice or ideas greatly appreciated!!
Oh its a 89 lux if it matters


also, uni's how hard are they to do at home? possible at all? again never done one, do you
need a press/puller or any special tools?

thanks




Image


Image


Image
Top
Posts: 39
Joined: Tue Sep 02, 2003 5:43 pm
Location: South West Vic

Post by 4wheelsdriven »

i would be checking the pinion brearings
Top
Posts: 2254
Joined: Tue Dec 10, 2002 5:09 pm
Location: Sydney

Contact:
Contact jessie928

Post by jessie928 »

hi man

your swivel hub bearings look BADLY buggered.

you dont need a press for uni's

Jes
ATTACH BROKEN TOYOTA HERE--->
DUCATI <-----Worlds best warning label
Top
Posts: 675
Joined: Sat Dec 17, 2005 10:06 pm
Location: campbelltown

Post by Nat84 »

X2

put one of these kits through it and then your good to go

http://cgi.ebay.com.au/Toyota-Landcruis ... 240%3A1318
Tires are like boobs, they always look big until you have played with them for a while, then you just want a bigger set
Top
Posts: 48
Joined: Thu Jan 17, 2008 4:41 pm
Location: South Brisbane

Post by zero »

Thanks guys..

will give that kit a go, and will try tackle the uni's my self any tips?
Top
Posts: 98
Joined: Tue Jul 15, 2008 2:53 pm
Location: Eumundi

Post by BeauGQ »

yeah get yourself a good pair of circlip pliers makes life bit easyer
middy cruiser 2" bodylift,2" lift
dual bat, pto winch, bar stainless roof and light racks and 80 series with EFS/procomp 5"sus, 33"BFG KM2s
Top
Posts: 1719
Joined: Sun Jan 25, 2004 11:45 am
Location: Brisbane

Contact:
Contact RV80

Post by RV80 »

zero wrote:Thanks guys..

will give that kit a go, and will try tackle the uni's my self any tips?

Get a good bench vice if you dont have one. Makes life easier when putting the new uni's in.
Top
Posts: 3725
Joined: Wed Jun 30, 2004 1:45 pm
Location: Blue Mountains, or on a rig somewhere in bumf*ck idaho

Post by rockcrawler31 »

Um. before you go pulling down the entire front end to check the king pins (i believe this is what you guys meant by pinion bearings - the pinion is in the diff centre)

jack up the front tyre. have a mate grab the top and bottom of the tyre and rock the tyre back and forth. If the entire swivel housing rocks and has play then the king pin bearings require attention. If the tyre moves and the swivel housing stays fairly still then the WHEEL bearings are in need of attention.

I'd be VERY surprised if the king pin bearings are stuffed. It doesn't happen often unless they've had a pretty hard life.
http://www.populationparty.org.au/
Top
Posts: 2254
Joined: Tue Dec 10, 2002 5:09 pm
Location: Sydney

Contact:
Contact jessie928

Post by jessie928 »

rockcrawler31 wrote:Um. before you go pulling down the entire front end to check the king pins (i believe this is what you guys meant by pinion bearings - the pinion is in the diff centre)

jack up the front tyre. have a mate grab the top and bottom of the tyre and rock the tyre back and forth. If the entire swivel housing rocks and has play then the king pin bearings require attention. If the tyre moves and the swivel housing stays fairly still then the WHEEL bearings are in need of attention.

I'd be VERY surprised if the king pin bearings are stuffed. It doesn't happen often unless they've had a pretty hard life.
that was only said once, i said swivel hub bearings :)

Jes
ATTACH BROKEN TOYOTA HERE--->
DUCATI <-----Worlds best warning label
Top
Posts: 5179
Joined: Fri Dec 05, 2003 8:15 pm
Location: Brisbane Australia

Post by Shadow »

rockcrawler31 wrote:Um. before you go pulling down the entire front end to check the king pins (i believe this is what you guys meant by pinion bearings - the pinion is in the diff centre)

jack up the front tyre. have a mate grab the top and bottom of the tyre and rock the tyre back and forth. If the entire swivel housing rocks and has play then the king pin bearings require attention. If the tyre moves and the swivel housing stays fairly still then the WHEEL bearings are in need of attention.

I'd be VERY surprised if the king pin bearings are stuffed. It doesn't happen often unless they've had a pretty hard life.
my swivel hub bearings collapsed in exactly the same manner as above, and the car looked exactly the same as zero's does. Except the wheel was leaning in at the top when mine went (might indicate the top has failed on his, as the bottom failed on mine, making it lean in at the top)

Car had been in 4wd about 4 times in its life.

I would still be doing as you suggest tho, jack it up and give the wheel a shake.

Mine moved freely about 60mm.
Top
Posts: 98
Joined: Tue Jul 15, 2008 2:53 pm
Location: Eumundi

Post by BeauGQ »

haha im doin this to my cruiser right now fuckin sucks
middy cruiser 2" bodylift,2" lift
dual bat, pto winch, bar stainless roof and light racks and 80 series with EFS/procomp 5"sus, 33"BFG KM2s
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 111 guests