Sorry to see that Bendev.
That reminds me, must check whether my diffs are alloy or steel...
I have a front steel bash plate from Fordy1 which would have prevented that, I hope.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Goodbye Jimny, Hello 02 G/Vitara(FS: Old Susspension)
99% that was torque not impact. It was bound to happen eventually.
That's an alloy housing. Time for a manual V6 GV or XL-7 steel housing methinks.
That's an alloy housing. Time for a manual V6 GV or XL-7 steel housing methinks.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Have to agree with Gwagensteve looks like torque not impact.
Do you have a front diff locker?
I know you have drop brackets and you got about 31/2 to 4inch lift right.
Not 100% sure but the angle of the cv can put strain on the diff housing, if at too much angle.
I have the drop brackets (Calmini 3” lift) on my Vit but my front diff is lower.
The bash plate on mine has saved it from damage.
Do you have a front diff locker?
I know you have drop brackets and you got about 31/2 to 4inch lift right.
Not 100% sure but the angle of the cv can put strain on the diff housing, if at too much angle.
I have the drop brackets (Calmini 3” lift) on my Vit but my front diff is lower.
The bash plate on mine has saved it from damage.
Suzuki Vitara JX 1.6 EFI Hardtop.
Calmini Lift, Rockhopper, Skid Plates, ARB Airlocker, Bullbar, 30" MTR, Custom Sill Sliders, Rear Bar.
See my pics
http://community.webshots.com/user/suzukiboyoz
Calmini Lift, Rockhopper, Skid Plates, ARB Airlocker, Bullbar, 30" MTR, Custom Sill Sliders, Rear Bar.
See my pics
http://community.webshots.com/user/suzukiboyoz
FUBAR
---------===== LOWRANGE JUNKIE =====---------
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
hey everyone,
There was no impact on the diff, I was trying to climb this hill where I had no traction because i was crossed up. You know what I mean, All the weight on the rear left and front right. Anyway as i was just sitting there bouncing spinning the wheels trying to get out of where I was, I heard this god all mighty crack and that was it, Diff gone.
Today I've found me a metal one, Yeeee Haa (in Power Barne commercial accent) and I'm on my way to pick it up now. The diff. I took out had 39 teeth and 8 teeth so I believe the ratio is a 4.875:1. Anyway hears a some photos of what was left of the diff I tool out or the car.
There was no impact on the diff, I was trying to climb this hill where I had no traction because i was crossed up. You know what I mean, All the weight on the rear left and front right. Anyway as i was just sitting there bouncing spinning the wheels trying to get out of where I was, I heard this god all mighty crack and that was it, Diff gone.
Today I've found me a metal one, Yeeee Haa (in Power Barne commercial accent) and I'm on my way to pick it up now. The diff. I took out had 39 teeth and 8 teeth so I believe the ratio is a 4.875:1. Anyway hears a some photos of what was left of the diff I tool out or the car.
Good Bye Grand Vitara, Hello 100 Series.
top job thats one fcuked diff, I imagine mine doing the same thing!!
how much did you pay for the steel housing? PM me if you want.
how much did you pay for the steel housing? PM me if you want.
---------===== LOWRANGE JUNKIE =====---------
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
I was looking at the build pics and the tension that the dif drop put on it combined with the power and hopping caused a stress failure.If you look at the pic off the center cross member mount,at the angle sitting on the bushing,after the build, then look at the angle after it broke you'll see the pinion returned to its original position.Thats a lot of strain on a cast housing combined with some heat from working hard.Solid steel axle housing is the way to go.
Hey atari4x4,atari4x4 wrote:top job thats one fcuked diff, I imagine mine doing the same thing!!
how much did you pay for the steel housing? PM me if you want.
I spoke with the people at Suzi4Wreckers and they great. I paid $360 for everything. I think the break up was $100 for housing and $250 plus $10 for something else. I got the steel one out of the LWB Manual Grand Vitara. I'm working over the week end but as soon as I can I'll take some photos of the new stuff before I put it together and get it in the car.
Good Bye Grand Vitara, Hello 100 Series.
Yeah I drove it home. I simply unlocked the manual hubs and took it out of 4WD. That way the CV shafts didn't turn and the diff. just hang there.grazza wrote:So did you manage to drive home? I imagine you could still drive with manual hubs, or remove the hub centre thingo.
Basically all the oil was drained out in the bush so there was nothing left to leak on the road.
Good Bye Grand Vitara, Hello 100 Series.
Hey I was thinking of getting two new CV shafts while its out (haven't decided yet) but can you please show me which photo and what you think the problem is.kottunmewth wrote:Looking at the CV axle on the passenger side,you mite want to check it out real good before reinstall.
After seeing that, im thinking a toyota solid axle swap for my GV mite be some thing worth looking into.Good luck.
Good Bye Grand Vitara, Hello 100 Series.
Yeah all photos to cover the article where shot and it happened at the end when I was just playing around. They took photos of the breakage as well.Squik wrote:CrapMight I say you did a damn fine job on it though
Did you get enough stuff shot first?
Awesome to see more Zooks in the mag too
Good Bye Grand Vitara, Hello 100 Series.
Hey I was thinking of getting two new CV shafts while its out (haven't decided yet) but can you please show me which photo and what you think the problem is.
Code: Select all
[img]
I hope that loaded the image,but one pic showing the pinion and pieces hanging by pas. side upper support.The end of the CV were the oil seal is if that is buggered up by the broken edge of the axle case the seal mite fail later.Being an 02 ,not sure of mileage ,the CV mite not have been replaced on the life of the vehicle,so just a thought since you rebuilding the front end.You defiantly need new ring and pinion.Be sure to clean up rest of differential parts of all metal shaving.Ive done some research and the design of the front end or the Vitaras and GV are pleged with seal failures on passenger side because there isn't a lot of bearing support.Were the driver side has a long shaft.They have a poly bushing you can get from suzuki dealer that goes on the passenger side that inserts into the dif. end to help keep the end were the passenger side CV inserts into the dif. tight to keep it from wallering out the differential and causing failure of the seal.
http://www.suzuki-forums.com/suzuki-vit ... ntial.html
Here is a link,It'll tell you about it.This site also has a lot of info on that model zuk and there are suzuki mechanics that visit that site I have talked to that will give you real answers to hard questions with out a load of srcap added in.
http://www.suzuki-forums.com/suzuki-vit ... ntial.html
Here is a link,It'll tell you about it.This site also has a lot of info on that model zuk and there are suzuki mechanics that visit that site I have talked to that will give you real answers to hard questions with out a load of srcap added in.
Went down to Suzi4wreckers last Friday and got a metal front diff and center from a manual LWB Grand Vitara. Lets see if I break this one!
Hopefully I should have it together and in the car this Wednesday, I'm just waiting on a new set of diff seals.
Here are some pictures of my new diff.
Hopefully I should have it together and in the car this Wednesday, I'm just waiting on a new set of diff seals.
Here are some pictures of my new diff.
Good Bye Grand Vitara, Hello 100 Series.
hey the pinion mounts look different on the new one compared to the old one, can it be adapted?
---------===== LOWRANGE JUNKIE =====---------
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
Shit, I didn't notice that. I don't have a day off till Wednesday so I'll have to check it out then. I can't see it being to much trouble. I hope.atari4x4 wrote:hey the pinion mounts look different on the new one compared to the old one, can it be adapted?
Hey, If anyone has seen this problem is it an easy fix.
Good Bye Grand Vitara, Hello 100 Series.
thats good news for you, i'm running the calmini kit & the pinion mount is like your original one so i'll need one off an early GV.
i'm guessing that might be off an XL~7 or very late GV?
i'm guessing that might be off an XL~7 or very late GV?
---------===== LOWRANGE JUNKIE =====---------
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
See you got the good stuff there bendev,A word of caution for ya.The vertical rubber mount is more flexible on twisting then a horizontal mount is.If you have trouble getting the axle to twist and line up to bolt the 1" drop brackets up ,talk to a machine shop you trust and see if they can drill or cut out the 2 holes were the bracket mounts to the pinion housing to allow the pinion to turn a little bit and let the mount on the cross member to stay straight. so the new cross member support bracket wont be in such a bind.
Well you got your work cut out for ya,good luck with it.
Well you got your work cut out for ya,good luck with it.
Firstly, to all on the forum, I'de like to say thank you all for your input and knowledge, especially Fordy1, for taking the time out and giving me a phone call and helping me out.
The front end was sorted out and went together fine, with not that much trouble at all.
As soon as I got it back together I called up some mates and went straight out to the seine of the crime, and what a day we had. Apart from me getting stuck in the mud and letting some water in, the GV went fine.
Check out some photos.
The front end was sorted out and went together fine, with not that much trouble at all.
As soon as I got it back together I called up some mates and went straight out to the seine of the crime, and what a day we had. Apart from me getting stuck in the mud and letting some water in, the GV went fine.
Check out some photos.
Good Bye Grand Vitara, Hello 100 Series.
Who is online
Users browsing this forum: No registered users and 73 guests