Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
front wheel bearing issues
front wheel bearing issues
had my front wheel bearings done by a local mechanic at the same time as having swivel hubs and seals etc done. Since having them done they are constantly coming lose. Within a matter of 2 weeks of normal driving they are noticabley lose (rattling, shaking and carrying on when turning or coming down from speed). Have had them tightened twice and now they are lose again!! Different place did them second time as i was in a hurry on my way out of town for the weekend.
Any ideas?? did i get dodgy bearings? over / under tensioned?
getting sick of this
cheers
Any ideas?? did i get dodgy bearings? over / under tensioned?
getting sick of this
cheers
GQ i assume?
They have a real crappy lock washer setup.
The GU has a proper keyed and bolted lock washer.
When the threads on the stub axle get fretted they never really lock properly again.
I think the GU lock washer setup will fit the GQ spindle...?
They have a real crappy lock washer setup.
The GU has a proper keyed and bolted lock washer.
When the threads on the stub axle get fretted they never really lock properly again.
I think the GU lock washer setup will fit the GQ spindle...?
Locktup4x4.com.au - For all of your hardcore gear
Outlaws4x4.com
Outlaws4x4.com
Yep, everyone does, esp if they reuse the lock washer and don't tighten the lock nuts properly. They need to be torqued up, not tightened and then backed off like you do with other types. It happens mostly on the left side. Best solution is to use the lockable nuts, as already suggested, but you'll need to make up a special tool to tighten them.rumpig89 wrote:yeh its a gq. do other people have this problem??
thanks alot for your responses.AJS wrote:Yep, everyone does, esp if they reuse the lock washer and don't tighten the lock nuts properly. They need to be torqued up, not tightened and then backed off like you do with other types. It happens mostly on the left side. Best solution is to use the lockable nuts, as already suggested, but you'll need to make up a special tool to tighten them.rumpig89 wrote:yeh its a gq. do other people have this problem??
i was just reading on 'exploreoz' that they need to be tightened to 167-196Nm, spin the wheel a few times, then back off to 0Nm, then tighten to 3.5Nm. does this sound right??
I noticed u said they need to be 'torqued up' does this mean dont back them off that all?? Torque settings? cheers
i just did the wheel bearing on my car,
The hubs have always been hot after a drive around.
its been about 100km so far and havent noticed any issues with it yet. gulp.
I tightened them up just using a punch and a hammer (only thing i had), spun the wheel a few times and then jammed them on again just not as tight.
I'm starting to think i should pull them apart and check them again.
The hubs have always been hot after a drive around.
its been about 100km so far and havent noticed any issues with it yet. gulp.
I tightened them up just using a punch and a hammer (only thing i had), spun the wheel a few times and then jammed them on again just not as tight.
I'm starting to think i should pull them apart and check them again.
No, what you said is correct for the adjusting nut. What I meant was don't just tighten them up and then back off a quarter turn (like I used to do), use the correct torque settings. You then put on a new lock washer and tighten the lock nut to the specified torque setting (167 - 196 NM).rumpig89 wrote:thanks alot for your responses.AJS wrote:Yep, everyone does, esp if they reuse the lock washer and don't tighten the lock nuts properly. They need to be torqued up, not tightened and then backed off like you do with other types. It happens mostly on the left side. Best solution is to use the lockable nuts, as already suggested, but you'll need to make up a special tool to tighten them.rumpig89 wrote:yeh its a gq. do other people have this problem??
i was just reading on 'exploreoz' that they need to be tightened to 167-196Nm, spin the wheel a few times, then back off to 0Nm, then tighten to 3.5Nm. does this sound right??
I noticed u said they need to be 'torqued up' does this mean dont back them off that all?? Torque settings? cheers
The hub nuts actually take a 53 MM socket, not 54 like most people think. Having that extra slop in there also doesn't help when you're trying to torque them up. Having said that, a lot of people just tighten everything up with a hammer and chisel whilst reusing the old washers, and don't have any problems. Personally, I gave that method away after my first loose wheel.
The brakes will heat up the hubs alot more than over tight bearings will. As long as you have good quality grease and new bearings then you wont have a problem better too tight than too loose especially with bigger tyres/wheels.nellyb1 wrote:i just did the wheel bearing on my car,
The hubs have always been hot after a drive around.
its been about 100km so far and havent noticed any issues with it yet. gulp.
I tightened them up just using a punch and a hammer (only thing i had), spun the wheel a few times and then jammed them on again just not as tight.
I'm starting to think i should pull them apart and check them again.
Wtb, 105 series rear tyre carrier, alloys and tyres.
Another thing I should have mentioned before: If you ever have to reuse an old lock washer, the most important part to check is not actually the washer surface but the little tab that slots into the keyway on the stub axle shaft. If the tab has been worn down, the washer wont grip on the shaft and will then allow the nuts to undo with the rotation of the wheel.
Even if you do use a brand new washer, you need to be careful when you tighten the locknut up because sometimes it grips the lock washer, turns it and in doing that, strips the tab off. That's why it's best to use the correct socket and torque settings. Even better is to replace the nuts as suggested.
Even if you do use a brand new washer, you need to be careful when you tighten the locknut up because sometimes it grips the lock washer, turns it and in doing that, strips the tab off. That's why it's best to use the correct socket and torque settings. Even better is to replace the nuts as suggested.
front wheel bearings
Fit the Gu setup it is much better and will fit the GQ, i'm on my third GQ and have fitted these to each one.
Who is online
Users browsing this forum: No registered users and 3 guests