Made from pvc pipe, it will probably break one day if i hit it hard enough, but i bought a 3m length for $12 so i have plenty off off-cut to repair it if need be.
Mike
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
$20 Snorkle
Master of my own domain
$20 Snorkle
Just finished making my snorkle. Its not the prettiest thing around, i'll admit that, but it does the job. Plus it cost next to nothing to make.
Made from pvc pipe, it will probably break one day if i hit it hard enough, but i bought a 3m length for $12 so i have plenty off off-cut to repair it if need be.
Mike
Made from pvc pipe, it will probably break one day if i hit it hard enough, but i bought a 3m length for $12 so i have plenty off off-cut to repair it if need be.
Mike
X2!!PJ.zook wrote:lol i dont think theres many a zook owner around who hasnt had a PVC snorkel at one stage or another. Good work
Good job mate.. should work a treat!
F&R ARB air lockers, lux diffs, 4 link coil rear, drop shackles, inboarded ranchos, stage 4 reduction gears, 35" silverstones, 9500 winch, RUF, 1.6 EFI, swimming goggles
The noise they make when they explode on a tree is something to behold apparently. I've said it before but I'll say it again that industrial vacuum hose is the best budget snorkel IMHO as it's dirt cheap, won't ever break and won't damage panels in a flop.
Build Thread - http://www.outerlimits4x4.com/viewtopic.php?f=16&t=168546&p=1927514&hilit=GRPABT1%27s+zook#p1927514
Master of my own domain
I did buy a 45 bend also (actually a 48 i think?? they dont come 45 exact) but it didnt follow roof exactly, and with a bit of angled rain i think it would have got into the snorkle tube pretty easily. with the 90, there is basically no chance.flaxton wrote:that pvc snokel is sweet man but i think maybe a 45 bend on the top so it follows the roof would make it even more better
I noticed a 3-4 mm hole in the bottom of the air box, im assuming its for water to drain out of. How effective is it? has anyone made up a bigger drain hole with 1 way valve?
If there were to be damage to the pvc, i dont think it will be likely to damage other panels. Would steel be more likely to damage panels if it were hit? wouldnt a steel tube crush, or rip mounting brackets out if hit also?
I could quite easily replace the main snorkle tube with steel (or stainless), the elbow where it actually goes into the guard is a rubber elbow (part of the factory system). I used rubber here so the whole system wouldnt be 'solid' and if the main tube did break, it wouldn't put any force into any of the internal pipework.
And as i said before, this snorkle was built on a tight budget, and could definately be done with more attention to detail (even the hole i cut in the guard!) but it will work when i need it. I've been wanting a snorkle for a while, and when i heard a mate of mine almost stuffed his engine (swallowed a mouthful of water) i nocked this baby up one morning a couple days later!
Mike
Ive had my pvc snorkel for while now, have smacked tree's at speed and only copped paint damage. ive also made mine connect to the windscreen frame so that under a real heavy impact it comes away from the bracket. unlike the mandrel bent exhaust one i seen which wrecked a windscreen frame when it didnt bend or pull away from the vehicle.
chop
chop
I THINK ICAN, I THINK I CAN!
$20 snorkel
i just made this one today, its 99 % finished
I had this 2 1/2 inch stainless steel snorkle made up at a local exhaust shop a couple of weeks ago. I then had it polished. All up it cost a bit more than $20 though... I figured i've gone this far with the truck, what's a few hundred more dollars.. haha... It's fixed to the "A" pillar with the use of nutserts. Anyways, i finished it off last night and i'm stoked with the end result 
This is the snorkel un-polished
The 2 nutserts in the "A" Pillar
The snorkle after being polished
This is the snorkel un-polished
The 2 nutserts in the "A" Pillar
The snorkle after being polished
2007 Jeep Wrangler JKU - CRD
Master of my own domain
Who is online
Users browsing this forum: No registered users and 68 guests