Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

lukey extractors

Tech Talk for Ford, Mazda, Daihatsu & Makes that currently dont have a home.

Moderator: Tiny

Forum rules
Post Reply
Posts: 36
Joined: Fri Oct 24, 2003 10:07 pm

lukey extractors

Post by yoda »

Any of you guys and girls ever had dealings with lukey (ozi brand) Ihave seen the pic of the headers they make and it is a nice 4-2-1 desighn wich should boost low rev power. Never heard of them before. NZ$281 wich is not half bad. What was the cost of the huricanes guys and are they 4-1 or 4-2-1 as I have 4-1 on at the moment but I want the low end power its not a dragster so the 4-1 is a bit of a misfit.
SA Kiwi damd what a combo. Mus have been made in bog.
Top
Posts: 4760
Joined: Mon Dec 30, 2002 6:04 am
Location: Adelaide

Contact:
Contact murcod

Post by murcod »

Yoda, are you sure the Lukey's are 4-2-1? Kent's got them on his USA Rocky and said they were 4-1, he posted a pic of them on here somewhere...

Hurricanes are 4-2-1 I posted pics of them on here a couple of weeks ago. I paid around $280 AUS including 10%GST.
David
Top
Posts: 36
Joined: Fri Oct 24, 2003 10:07 pm

Post by yoda »

jep spoke to the guy today had one in stock look under daihetsu feroza it shows a picture
http://www.partsco.com
SA Kiwi damd what a combo. Mus have been made in bog.
Top
Posts: 4760
Joined: Mon Dec 30, 2002 6:04 am
Location: Adelaide

Contact:
Contact murcod

Post by murcod »

Whoa!

I just checked that site and can tell you for sure that pic isn't of the Lukey headers to fit a Feroza!

Image

For a start Lukeys are coated in some special black heat resistant paint, and they're chrome. The spacing is all wrong for the exhaust ports too- check the pic below of my Hurricanes for a comparison:

Image

Finally, here's the pic of Kent's Lukeys (complete with Lukey badge) and they're definitely 4-1. So unless Lukey make two different sets of headers for Feroza's that joint is feeding you a load of bull****! :D ;)

Image
David
Top
Posts: 4760
Joined: Mon Dec 30, 2002 6:04 am
Location: Adelaide

Contact:
Contact murcod

Post by murcod »

PS: Yoda, go back to the Partsco site and get the Feroza extractor page up, then click on the Rocky page........ the picture doesn't change! :D
David
Top
Posts: 1
Joined: Fri Jan 30, 2004 11:08 am

Post by Rock »

The picture of the Extractors on www.PartsCo.Com are for the Rocky Diesel. (I must fix that).

Here is a bad picture of the Lukey Feroza LPH601 Extractors.
Top
Posts: 4760
Joined: Mon Dec 30, 2002 6:04 am
Location: Adelaide

Contact:
Contact murcod

Post by murcod »

Hi Rock, thanks for the pic.

They look like 4-1, the same a Kent's pic above??? (although it is a bit hard to tell from that angle?)
David
Top
Posts: 36
Joined: Fri Oct 24, 2003 10:07 pm

4-2-1

Post by yoda »

I realy hope you guys are wrong about this. Does anyone have huricane's web page. PLEASE before I kill a salesman
SA Kiwi damd what a combo. Mus have been made in bog.
Top
Posts: 4760
Joined: Mon Dec 30, 2002 6:04 am
Location: Adelaide

Contact:
Contact murcod

Post by murcod »

Liverpool Exhaust in Sydney make them. They don't have an Email address on their website though- Simply PV has been through all that......
David
Top
Post Reply

Return to “Ford / Mazda / Daihatsu / Homeless”

Who is online

Users browsing this forum: No registered users and 1 guest