Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

1HD-T big end bearings

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 382
Joined: Fri Dec 06, 2002 8:15 pm
Location: Diamond Creek

Contact:
Contact DNA Off Road

1HD-T big end bearings

Post by DNA Off Road »

Hi all,

I have a ’93 1HD-T in an 80 series that has just gone past 100,000. Should I be replacing the big end bearings?

Cheers
Stock 'Cruiser X 2
www.dnaoffroad.com.au
Top
Posts: 2585
Joined: Fri Mar 28, 2008 4:45 pm
Location: SYDNEY

Post by thehanko »

first thing you need to do is drive it more! 100,000 in 16 years. wow!

but i have no useful information for you. sorry
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Top
Posts: 1383
Joined: Tue May 06, 2008 8:12 pm
Location: Newcastle

Post by oldmate »

It wouldn't hurt. It's not an expensive job to pay for (n o more than 500 bucks) and it would give you peace of mind.
Top
Posts: 93
Joined: Mon May 18, 2009 9:44 pm
Location: mornington

Post by kane077 »

If you have 100k already and it hasnt blown up what makes you think it will now? I personally wouldnt be too concerned about it.
Top
Posts: 1042
Joined: Mon May 05, 2008 6:33 pm
Location: MACKAY

Post by SIMMO84 »

kane077 wrote:If you have 100k already and it hasnt blown up what makes you think it will now? I personally wouldnt be too concerned about it.
X2 100k isnt barely run in unless u have oil pressure problems I wouldnt wrooy about it.
Top
Posts: 40
Joined: Mon Dec 01, 2008 8:06 am
Location: Perth

Post by rapid80 »

I would if I was you. The bearings have a history of delaminating around 100k and don't give any signs until just before they fail. Some cases have had about 60km from the 1st sign of change in oil pressure/tapping sound to a complete failure. Check the lcool website if you want photos or more info.There is a stack of storys about failures including vented blocks etc.Its worth it just for the peace of mind.If you're not the 1st owner maybe check the history as many were already done,some under warranty.
Top
Posts: 6
Joined: Thu Feb 05, 2009 11:32 am
Location: Gympie

Post by Adammu »

I would for sure.. i did mine at 300 k and was a bit hesitent at spending the $ but am glad i did one of them had the early signs of failure...

$500 or so is alot cheaper then $4000 +
Top
Posts: 141
Joined: Thu Aug 23, 2007 5:00 pm
Location: Rockhampton

Post by horndog »

Yeah do it for sure. the early 1HDTs had a bad batch of bearings in the bottom end. not sure if its up till 93 tho. my dads blow the bottom end because the bearing failed and that was only at 130 000. his was a 92 i think. I no its a different motor but just stripped down an early 1hz which still runs the same crank and bearing as the factory turbo. it had 200 on the clock and one bearing had nothing left of it. crank was running on the rod. all the other bearings had decent chunks missing of them to.
Top
Posts: 2097
Joined: Tue Aug 12, 2003 6:50 pm
Location: wollongong

Post by dow50r »

Your mad if you do and mad if you dont, so do it....a mate has done it twice and both times, bearings came out looking bad....
Andrew
Confucious say...man who argue with idiot, worserer himself
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 1 guest