Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Hi Beam on = ALL LIGHTS OUT??

For all things Electrical.

Moderator: -Scott-

Post Reply
Posts: 1363
Joined: Tue May 13, 2003 10:54 am
Location: Scarborough, Qld

Hi Beam on = ALL LIGHTS OUT??

Post by bigbluemav »

Hi All

Not 4b related, but electrical!!

My little junker Laser (1991 KH) has an electrical problem. The first time I took it out at night, I found it had no instrument lights, no tail lights and when you switch to high beam, the headlights went out. However, when you flash the high beam, it works brilliantly.

The instrument and tail lights I fixed easily (fuse :oops: ), but the high beam issue persists. I'm thinking the switch block (on the indicator stalk) is shagged, I just wanted to check to see if there could be any other likely reason BEFORE I go the trouble and expense of getting another indicator stalk/switch block.

Any assistance gratefully accepted.
Big Dave, Scarborough, Qld
Loose Screws 4wd Racing Team
Posts: 244
Joined: Mon Jun 23, 2008 7:37 am
Location: Clarence Valley NSW

Post by KUSTOMV840 »

See if there is a relay on your headlight circuit. Sounds like a bad earth to me.... Do you have driving lights too?
Definition of having balls: to come home drunk smelling of perfume, slapping the wife on the arse and saying 'Your next fatty"!
Posts: 14209
Joined: Sun Jan 11, 2004 11:36 am
Location: Adelaide

Post by -Scott- »

This sounds a bit like an issue I had in my Sigma a few years back. It drove me crazy for days, until I discovered a dud earth contact in a connector in a different part of the loom.

I doubt I would have found it without a wiring diagram - do you have a Gregory's manual?
Posts: 1363
Joined: Tue May 13, 2003 10:54 am
Location: Scarborough, Qld

Post by bigbluemav »

Hi Scott

I just bought a Haynes manual for it so I'll check where the earth/s is/are in the high beam circuit.

There's no extra electrical accessories added, so I guess it'll just be a matter of trace and test! BUMMER!!

Ta though!
Big Dave, Scarborough, Qld
Loose Screws 4wd Racing Team
Posts: 95
Joined: Mon Feb 10, 2003 8:09 pm
Location: Traralgon

headlights

Post by RRover85 »

it sounds like the headlight switch... lasers dont have a relay I think and this is the problem, all the load of the high beams run through the switch contacts and over time they get dirty and burnt and once there is a load on your headlight switch you will loose all lights...

most switchs can be pulled apart and the contacts cleaned which should last you a couple of years or so...
Posts: 2134
Joined: Tue May 11, 2004 6:03 pm
Location: Armidale

Post by BOGAN V8 »

My Girlfriend has a 91 laser that had the same problem.. pulled the headlight/dipper switch apart and cleaned the contacts with a nail file fixed all good..

Only had the car for a couple of hours after purchase was driving it home in the dark and flicked to high beam and boom no lights scared the crap outta me for a few seconds...
94 HJZ 80 GXL 4 Inch lift 35s. TJM Accessories Front to back
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest