Hey all... i can't seem to find a decent price on either a zlink or a dropped pitman arm to make my spoa conversion complete (and correct). Does anyone have one they'd like to sell? Does anyone know which one is a better choice? Maybe i could just chop my old pitman in half and weld some middle piece in, to make it a "dropped pitman arm" hehe... any thoughts on this?
at
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
WANTED: zlink or dropped pitman
WANTED: zlink or dropped pitman
I love Sarah :)
ALSO NEED: drive shaft spacers
hi steer? Never heard of that. How much does that cost for a sammy... any idea?
Anybody have some drive shaft spacers ?
at
Anybody have some drive shaft spacers ?
at
I love Sarah :)
no offense, but if i saw your zook on the road with a z link i would run you off the road so that i could be sure your zook wouldn't kill anyone/
just buy a zook high steer arm from m&m in windsor 0245 879811
it will be cheaper than buying a dropped pitman arm (once available from grp, but no longer) and heaps safer than a pre historic z link.
your zook will drive better also.
just buy a zook high steer arm from m&m in windsor 0245 879811
it will be cheaper than buying a dropped pitman arm (once available from grp, but no longer) and heaps safer than a pre historic z link.
your zook will drive better also.
planb wrote:no offense, but if i saw your zook on the road with a z link i would run you off the road so that i could be sure your zook wouldn't kill anyone/
Jeepers - that's a tad negative Planb
planb wrote:just buy a zook high steer arm from m&m in windsor 0245 879811
it will be cheaper than buying a dropped pitman arm (once available from grp, but no longer) and heaps safer than a pre historic z link.
your zook will drive better also.
Note that crombiex lives in the US - hense grimbo's suggestions of using (somewhat local) US suppliers of goodies rather than (local to us) Aussie suppliers.
DMA Founding Member #1 - Now Retired
hi steer should be used when performing a spring over. It places the steering above the spring pack instead of using the dodgy z-link.
We manufacture 2 kits, the first kit contains one hi steer arm and a draglink with quality ball joints. This kit places only the draglink above the spring pack.
The second kit contains 2 hi steer arms, tie rod and draglink with quality ball joints. This kit places the entire steering above the spring packs and greatly reduces the chance of damaging your steering.
The hi steer kits are available through M&M Custom Engineering or Overkill Engineering.
We manufacture 2 kits, the first kit contains one hi steer arm and a draglink with quality ball joints. This kit places only the draglink above the spring pack.
The second kit contains 2 hi steer arms, tie rod and draglink with quality ball joints. This kit places the entire steering above the spring packs and greatly reduces the chance of damaging your steering.
The hi steer kits are available through M&M Custom Engineering or Overkill Engineering.
so why are you saying the zlink is dodgy? considering its what used to be used. sure some might break , but if welded properly using 4140 cromoly steel there shouldn't be a problem with them breaking. no doubt the high steer is better but i think the z bar works fine.
if its worth doing do it intensly , better still do it with MADPASSION
set your limits way beyond your abilities
set your limits way beyond your abilities
I had a Zbar for few years and it was made properly, BUT I never felt 100% safe with it. The drag link has to be heated up to make the bends and that in turn fatigues it. And as it is a small diameter piece of metal than i reckon there is a reasonably high risk of one breaking compared to a straight hi-steer arm. I saw redzook's broken zbar (I had to pull it off and put my hi-steer on it so he could drive home) and i can tell you he was lucky it happened at a slow speed, and not going down the freeway at 110km/hr.
CAM
Wait a minute while I put on my asbestos overalls, zzzzzip thank you.
I have had a Z link in my 1.6l spoa 92 Sierra for years, and it has worked well for me.
I am running 33" tyres on OME springs, there is a bit of bump steer but I seem to be used to it, it is after all a Sierra not a ferrari
and should be driven acordingly.
I also worry about these histeer brackets that piggy back the calliper mounts, the tabs that are cast into swivel housing are designed to handle a rotating load not a load on this plane (I am not bagging histeers I am trying to get my head around them ).
I also question the legality of these brackets from an engineers certificate perspective, for the above reason.
The link it self, is still as good as the day it was installed, however my steering box (standard) has been leaking oil recently and I am wondering if the angle from one end of the Zlink to the other is putting an unreasonable side load on the box (I think so).
As I said I am not shit canning H/Steers just after feed back from those that know so I can make an informed decision before I spend my wifes hard earned money.
Peter.
I have had a Z link in my 1.6l spoa 92 Sierra for years, and it has worked well for me.
I am running 33" tyres on OME springs, there is a bit of bump steer but I seem to be used to it, it is after all a Sierra not a ferrari
and should be driven acordingly.
I also worry about these histeer brackets that piggy back the calliper mounts, the tabs that are cast into swivel housing are designed to handle a rotating load not a load on this plane (I am not bagging histeers I am trying to get my head around them
).
I also question the legality of these brackets from an engineers certificate perspective, for the above reason.
The link it self, is still as good as the day it was installed, however my steering box (standard) has been leaking oil recently and I am wondering if the angle from one end of the Zlink to the other is putting an unreasonable side load on the box (I think so).
As I said I am not shit canning H/Steers just after feed back from those that know so I can make an informed decision before I spend my wifes hard earned money.
Peter.
droopypete wrote:before I spend my wifes hard earned money.
Peter.
Piss funny mate.
Can you elaborate on your steering Damper placement, I noticed on the AT03 vid it appears to mount from the tierod to the diff housing, as I have left the steering damper out with the chassis extension I'm considering this,
Cheers
Steve
p.s. I never had any drama's with my z-link/dropped pitman arm setup either on my SPOA either.
yeshemesh
bigsteve wrote:droopypete wrote:before I spend my wifes hard earned money.
Peter.
Steve
p.s. I never had any drama's with my z-link/dropped pitman arm setup either on my SPOA either.
Steve I think it may be a case of we don't know what we are missing
when fitted, a histeer should make a dramatic diferance to the way it drives (I have never driven one so I am asuming) I am not disputing this, it is only the mounting of the arms and the engeneering aproval issues that are conserning me.
Peter.
ps I will bring your photos along to Wandin, are you coming up this arvo?
camskizook wrote:I had a Zbar for few years and it was made properly, BUT I never felt 100% safe with it. The drag link has to be heated up to make the bends and that in turn fatigues it. And as it is a small diameter piece of metal than i reckon there is a reasonably high risk of one breaking compared to a straight hi-steer arm. I saw redzook's broken zbar (I had to pull it off and put my hi-steer on it so he could drive home) and i can tell you he was lucky it happened at a slow speed, and not going down the freeway at 110km/hr.
My Zlink has not been heated at all camskizook.
do you have any pics of the breakage?
Also, no one has said anything about the how engineerable these hi steer arm are, has anyone had a set engeneered on there car?
Help me out here guys, I have questions that need to be answered
Peter.
The pics of the high steer look ok, I have seen other ones that use one of the cal bolts and locate on the king pin bearing locator, and another that only relies on the four little king pin bearing retianer bolts , the fact that these bolts need to be doubled in length to retian the high steer makes me sus on that one.
Red was your z bar engineer approved ?
Not stating that this makes it great just wondering .
Larry.
Red was your z bar engineer approved ?
Not stating that this makes it great just wondering .
Larry.
Dozoor wrote:The pics of the high steer look ok, I have seen other ones that use one of the cal bolts and locate on the king pin bearing locator, and another that only relies on the four little king pin bearing retianer bolts , the fact that these bolts need to be doubled in length to retian the high steer makes me sus on that one.
Red was your z bar engineer approved ?
Not stating that this makes it great just wondering .
Larry.
I have been running a home fabbed arm on those 4 lil bolts for serveral (6 or more) years now . the arm was actually made to slot over top of the king pin plate so the bolts are still "normal" length .. never really caused me any issues except once whe I forgot to locktight them properly and they worked loose ...
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Dozoor wrote:The pics of the high steer look ok, I have seen other ones that use one of the cal bolts and locate on the king pin bearing locator, and another that only relies on the four little king pin bearing retianer bolts , the fact that these bolts need to be doubled in length to retian the high steer makes me sus on that one.
Red was your z bar engineer approved ?
Not stating that this makes it great just wondering .
Larry.
nope dont think it was engineer approved
btw. Overkill didnt make the zbar
just though id say that so no1 though they did
Team UNDERDOG #233
WERock Australia thanks to
[url]http://www.longfieldsuperaxles.com[/url]
[url]http://www.rockbuggysupply.com[/url]
WERock Australia thanks to
[url]http://www.longfieldsuperaxles.com[/url]
[url]http://www.rockbuggysupply.com[/url]
droopypete wrote:camskizook wrote:I had a Zbar for few years and it was made properly, BUT I never felt 100% safe with it. The drag link has to be heated up to make the bends and that in turn fatigues it. And as it is a small diameter piece of metal than i reckon there is a reasonably high risk of one breaking compared to a straight hi-steer arm. I saw redzook's broken zbar (I had to pull it off and put my hi-steer on it so he could drive home) and i can tell you he was lucky it happened at a slow speed, and not going down the freeway at 110km/hr.
My Zlink has not been heated at all camskizook.
do you have any pics of the breakage?
Also, no one has said anything about the how engineerable these hi steer arm are, has anyone had a set engeneered on there car?
Help me out here guys, I have questions that need to be answered
Peter.
Well that is even worse if you bent it without heat.
CAM
camskizook wrote:droopypete wrote:camskizook wrote:I had a Zbar for few years and it was made properly, BUT I never felt 100% safe with it. The drag link has to be heated up to make the bends and that in turn fatigues it. And as it is a small diameter piece of metal than i reckon there is a reasonably high risk of one breaking compared to a straight hi-steer arm. I saw redzook's broken zbar (I had to pull it off and put my hi-steer on it so he could drive home) and i can tell you he was lucky it happened at a slow speed, and not going down the freeway at 110km/hr.
My Zlink has not been heated at all camskizook.
do you have any pics of the breakage?
Also, no one has said anything about the how engineerable these hi steer arm are, has anyone had a set engeneered on there car?
Help me out here guys, I have questions that need to be answered
Peter.
Well that is even worse if you bent it without heat.
Knowing Pete .. there would be a very good reason it was done that way, he does not do anything half assed .. His rig was\is engineered and rubber stamped etc as being so ..
Just from curiosity .. would you heat the tubing used to make bends in a roll bar
I sure as hell would not ... " If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
camskizook wrote:droopypete wrote:camskizook wrote:I had a Zbar for few years and it was made properly, BUT I never felt 100% safe with it. The drag link has to be heated up to make the bends and that in turn fatigues it. And as it is a small diameter piece of metal than i reckon there is a reasonably high risk of one breaking compared to a straight hi-steer arm. I saw redzook's broken zbar (I had to pull it off and put my hi-steer on it so he could drive home) and i can tell you he was lucky it happened at a slow speed, and not going down the freeway at 110km/hr.
My Zlink has not been heated at all camskizook.
do you have any pics of the breakage?
Also, no one has said anything about the how engineerable these hi steer arm are, has anyone had a set engeneered on there car?
Help me out here guys, I have questions that need to be answered
Peter.
Well that is even worse if you bent it without heat.
Worse than what, camskizook, you are being a bit agressive mate
.
I origionaly had a Z link that had reinforcing welded to the bends, it was made from heavier tube and welded by someone who knew what they were doing,and was plenty stout, the engineer prefered one made from 1 piece of solid rod, cold bent in the press, so that is what I did.
What did the engineer say about your hi steer?
Peter.
droopypete wrote:camskizook wrote:droopypete wrote:camskizook wrote:I had a Zbar for few years and it was made properly, BUT I never felt 100% safe with it. The drag link has to be heated up to make the bends and that in turn fatigues it. And as it is a small diameter piece of metal than i reckon there is a reasonably high risk of one breaking compared to a straight hi-steer arm. I saw redzook's broken zbar (I had to pull it off and put my hi-steer on it so he could drive home) and i can tell you he was lucky it happened at a slow speed, and not going down the freeway at 110km/hr.
My Zlink has not been heated at all camskizook.
do you have any pics of the breakage?
Also, no one has said anything about the how engineerable these hi steer arm are, has anyone had a set engeneered on there car?
Help me out here guys, I have questions that need to be answered
Peter.
Well that is even worse if you bent it without heat.
Worse than what, camskizook, you are being a bit agressive mate
I origionaly had a Z link that had reinforcing welded to the bends, it was made from heavier tube and welded by someone who knew what they were doing,and was plenty stout, the engineer prefered one made from 1 piece of solid rod, cold bent in the press, so that is what I did.
What did the engineer say about your hi steer?
Peter.
Calm down...im not being agressive. The z-links I am talking about are those that take the original THIN drag link and are bent, however its done. What did the engineer say about mine? Absolutely nothing because i havent taken it to him. However my steering and diffs have come from a vehicle that was fully engineered with it.
CAM
camskizook wrote:Calm down...im not being agressive. The z-links I am talking about are those that take the original THIN drag link and are bent, however its done. What did the engineer say about mine? Absolutely nothing because i havent taken it to him. However my steering and diffs have come from a vehicle that was fully engineered with it.
That is exactly what mine is, and has been for years
and it has been pushing 13.5" wide tyres around the whole time.
Are you saying that the hi-steer was engineered on this previous vehicle camskizook?
Peter.
camskizook wrote:As far as i know, Yes.
That is good news, I will have to speak to my engineer then.
I still have concerns about the brackets, but I want to go this way, so the big Qustion is who do I speak to? I see there are a few people on this board selling them and I would like to support them if I can (one big happy family
) but is there anything else I should be looking at?
how much are they, whose is better and why, all that sort of stuff.
Thanks for getting me this far in my quest for a hi-steer.
Peter.
Who is online
Users browsing this forum: No registered users and 71 guests