factory locker into rb30

[THICKNICK]

searched to no success,

have a factory locker here came out of 4.2l with 4.1 diffs. wondering if i can put it into a rb30 with 4.3s. im guessing diff gears could just be changed and intake manifold would have to be modified for hose to vacuum locker, or can the one of the 4.2 manifold screw straight into the rb30 manifold and all be functional.

cheers for your input
nick

[jessie928]

searched to no success,

have a factory locker here came out of 4.2l with 4.1 diffs. wondering if i can put it into a rb30 with 4.3s. im guessing diff gears could just be changed and intake manifold would have to be modified for hose to vacuum locker, or can the one of the 4.2 manifold screw straight into the rb30 manifold and all be functional.

cheers for your input
nick

just change the gearset on the factory locker to 4.3 and bolt it in.
all you need is a nipple on one of the inlet manifold blanks and a line to the solenoids.
you are best off fitting the origional tank and 1 way valve aswell.

Jes

[TEAMRPM]

searched to no success,

have a factory locker here came out of 4.2l with 4.1 diffs. wondering if i can put it into a rb30 with 4.3s. im guessing diff gears could just be changed and intake manifold would have to be modified for hose to vacuum locker, or can the one of the 4.2 manifold screw straight into the rb30 manifold and all be functional.

cheers for your input
nick

Hi Nick,

Yes it will fit. obviously you will need to change your diff gears to match them up. you have to change the housing and all though not just the centre.

if you use the vacuum tank of the 4.2 that will be fine. make sure the one way valves get used as well. its an easy install once you get all the bits you need. if you just tap into the brake booster vacuum port and run a T to the vacuum tank that'd do it.

cheers

[THICKNICK]

searched to no success,

have a factory locker here came out of 4.2l with 4.1 diffs. wondering if i can put it into a rb30 with 4.3s. im guessing diff gears could just be changed and intake manifold would have to be modified for hose to vacuum locker, or can the one of the 4.2 manifold screw straight into the rb30 manifold and all be functional.

cheers for your input
nick

Hi Nick,

Yes it will fit. obviously you will need to change your diff gears to match them up. you have to change the housing and all though not just the centre.

if you use the vacuum tank of the 4.2 that will be fine. make sure the one way valves get used as well. its an easy install once you get all the bits you need. if you just tap into the brake booster vacuum port and run a T to the vacuum tank that'd do it.

cheers

thanks guys, i was sure it could be done, only other question wheres the vacuum tank on the 4.2.

[TEAMRPM]

searched to no success,

have a factory locker here came out of 4.2l with 4.1 diffs. wondering if i can put it into a rb30 with 4.3s. im guessing diff gears could just be changed and intake manifold would have to be modified for hose to vacuum locker, or can the one of the 4.2 manifold screw straight into the rb30 manifold and all be functional.

cheers for your input
nick

Hi Nick,

Yes it will fit. obviously you will need to change your diff gears to match them up. you have to change the housing and all though not just the centre.

if you use the vacuum tank of the 4.2 that will be fine. make sure the one way valves get used as well. its an easy install once you get all the bits you need. if you just tap into the brake booster vacuum port and run a T to the vacuum tank that'd do it.

cheers

thanks guys, i was sure it could be done, only other question wheres the vacuum tank on the 4.2.

It doesnt have to be a diesel, it can be the factory locker tank as they are the same vacuum tanks. you can use either.. go to the wreckers , should be cheap enough.

its plastic and aout 4" x 6" i diameter. generally located on the inner left hand guard, pending models.

good luck