Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Fuel Adjustment After Turbo Fitment

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Post Reply
Posts: 9
Joined: Tue Nov 27, 2007 1:24 pm
Location: Brissy

Fuel Adjustment After Turbo Fitment

Post by lilredluxury »

Well I finally got my Turbo installed and exhaust/crossover pipes done, installed a Pyro & Boost gauge and now im itching to get this thing back on the road. :D

What is the general consensus for the initial adjustment on the fuel max delivery?...1/2 turn....3/4 turn...1 turn... & what sorta temps should i be running the motor at? Its a 2.8 with a ct-20 off a 2lte surf (Ive installed the pyro just after the turbo with a new exhaust & 3in Dump pipe)

Also I think im going to just run with the standard boost that the turbo makes without employing the washer upgrade. :) What should the standard boost be on these motors by the way? :oops:
Posts: 658
Joined: Wed Feb 13, 2008 5:41 pm
Location: Brissy

Post by yamaha__308 »

Stock boost 8-9 psi ish?

I started with 1/2 turn in. And then re-adjusted for 500-550 at max load.

Any plans for an intercooler?
Posts: 9
Joined: Tue Nov 27, 2007 1:24 pm
Location: Brissy

Post by lilredluxury »

I think I'll do the same and start with 1/2 turn and see what effect that has. Would rather have reliabillity over performance, which can't be worse than before the turbo was bolted on. Nothing can be worse than it was !!! Ive been overtaken by a bloody Nissan with tinnie on the roof and van in tow going up a hill !!! Gee he was smiling as he drove past me :oops:

I have a standard cooler of a R33 riceline lying in the shed, but have no plans to install it at this stage, as it would require a bodylift to fit, plus i don't think the amount of work needed would be worth the performance gains it'd give me. (I stand to be corrected if any1 has fitted an intercooler and thinks it was worth while... any1 care to comment...?) I still have a lot to learn so I'll listen to everyone's opinion/experience before I make a descision...

Being that its a pretty small cooler, I think would be prone to heat soak, also I change my oil religeously every 4000kms so I dont wont to make it any harder to refill the oil by obstructing it.
Posts: 2585
Joined: Fri Mar 28, 2008 4:45 pm
Location: SYDNEY

Post by thehanko »

mine was about 3/4 of a turn in the end but yeah start off with 1/2.

mine only goes over 500 occasionally and very rarely but has been upto about 540. if that happens i back off to about 500 again just to be sure, even though rule of thumb is safe to 550.
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Posts: 75
Joined: Sun Aug 08, 2004 11:46 pm
Location: Perth

Post by tuffer_2.4 »

mine is intercooled and i have 2 turns in it runs 12psi and goes hard bit smokey down low though but i dont care
06 Hilux Locked Lifted and Bulk Panel Damage
Posts: 40
Joined: Sun Sep 18, 2005 11:54 pm
Location: Perth Western Australia

Post by Tim HJ61 »

I did three turns, but the real test is smoke.

Keep turning it until you get smoke under power, then back it off a bit. (provided your injectors are good)

Increasing boost will assist EGT's getting too high, but it's all a bit of a balancing act.

http://www.perth4x4.net/forum/showthread.php?t=28202

Tim
Posts: 2585
Joined: Fri Mar 28, 2008 4:45 pm
Location: SYDNEY

Post by thehanko »

Tim HJ61 wrote:I did three turns, but the real test is smoke.
???

the real test is egts, guess work off smoke is exactly that.

you risk goin a bit hot, might seem ok but be slowly melting vanes and what not generally weakening stuff until it craps out and destroys an engine which will cost more than a $120 dyno tune with egts.
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Posts: 658
Joined: Wed Feb 13, 2008 5:41 pm
Location: Brissy

Post by yamaha__308 »

thehanko wrote:
Tim HJ61 wrote:I did three turns, but the real test is smoke.
???

the real test is egts, guess work off smoke is exactly that.

you risk goin a bit hot, might seem ok but be slowly melting vanes and what not generally weakening stuff until it craps out and destroys an engine which will cost more than a $120 dyno tune with egts.
x2.

EGTs are the real test. Especially pre turbo.
Posts: 11
Joined: Fri Jul 24, 2009 11:58 am
Location: Cairns

Post by dabulg »

For about 400 hunjy you could have an aneroide fitted to take care of fuel flow. The fuel is controlled by boost automatically. Mine works really well and very little smoke at all rev ranges. I don't worry about a pyro because I confident the aneroide is not dumping too much fuel in there and taking EGT too high.
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest