Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Can you weld stainless steel to mild steel?

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Post Reply
Posts: 533
Joined: Sat Jan 15, 2005 4:54 pm
Location: Melbourne, Australia.

Can you weld stainless steel to mild steel?

Post by InSanE »

I have an airbox that I want to mod soon with 4" inlet and outlets and it is made from mild steel, and I have some 4" stainless steel tube left from when i did my snorkel and im just wondering if stainless with be ok to weld to mild steel?
GQ LWB TD42, boost, lockers etc

http://forum.mudrhino.com.au/viewtopic.php?t=262&start=30
Posts: 579
Joined: Mon May 29, 2006 4:36 pm
Location: Melbourne

Post by bigcam »

have tigged stainless to mild using argon and stainless rods quite regularly with success.
[quote="75 cruser"]we want more donkey[/quote]
Posts: 1413
Joined: Mon Aug 21, 2006 5:54 pm
Location: Perth

Post by Moph »

http://www.outerlimits4x4.com/ftopic186405.php

My thread about arc welding - can be done. Just picked up some 316L rods today from my local steel joint for a buck each (only needed a couple).
Posts: 810
Joined: Tue Jul 08, 2008 8:40 pm
Location: vic

Post by ajsr »

yes they weld togher perfectly ok
85 high roof 1.3, 6.5 tc, air lockers,ruf and 34 swampers. yep its an ugly pos.
Posts: 1039
Joined: Mon Mar 05, 2007 10:28 am
Location: On board the Mothership

Post by Harb »

As they say you can weld shite to a blanket as long as you use the right rods :D
Harb

http://www.4wdmonthly.com.au/shed/index.php?id=2244&im=1
Posts: 977
Joined: Sun Jul 20, 2003 7:57 pm
Location: Brisbane

Post by Gutless »

I have MIG'd stainless to mild successfully with both .9 mig wire and argosheild, and stainless mig wire and argon. Tig aswell.
[url]www.twinstickoffroad.com[/url]
Posts: 533
Joined: Sat Jan 15, 2005 4:54 pm
Location: Melbourne, Australia.

Post by InSanE »

im running a unimig portamig 200 on .8 flux cored wire will this be ok do you think ?
GQ LWB TD42, boost, lockers etc

http://forum.mudrhino.com.au/viewtopic.php?t=262&start=30
Posts: 848
Joined: Fri Apr 02, 2004 12:01 pm
Location: Central Victoria

Post by Patroler »

have used 316L and er70s4 (LW1) in the past to weld 304 and 316 to mild without any issues, i don't think youd have a problem, if in doubt do a test weld on some scrap and destructively test it!?
There are no stupid questions, but there are a LOT of inquisitive idiots
Posts: 26
Joined: Wed Jul 05, 2006 8:22 pm

Post by muckute »

I used a gasless mig with steel flux core to mod my exhaust using some stainless tube, this incolved mild-stainless and stainless-stainless. No issues so far and that was 2 yrs ago, only thing is it doesn't look quite as nice as if it had been done properly
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest