Guys,
some good stuff in here. Especially item29. "Can I install a supercharger"
http://www.geocities.com/endre_rl/isuzufaq.htm
Wayne
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Isusu FAQ US site
Moderator: Moderators
Isusu FAQ US site
Wayne.
But wait there's more. Here's another site with a pile of questions and answers for (I'll spell it right this time) 
Isuzu owners.
http://www.automotivehelper.com/cat240/
Did the regrease of the tail shaft splin on the weekend and I'll be..... it worked. No more thunk noise.
Wayne.
Isuzu owners.
http://www.automotivehelper.com/cat240/
Did the regrease of the tail shaft splin on the weekend and I'll be..... it worked. No more thunk noise.
Wayne.
Wayne.
Hi Greg,
fairly straight forward. I firstly jacked up one rear wheel to allow me to rotate the drive shaft. You get to see how much slip you have in your LSD this way, but it will turn. Then under you go:
1. Mark with chalk the position of the front universal to the gearbox output coupling as a reference for reassembly.
2. Prise off only the rear facing ring clamp that holds the boot over the spline. The front one doesn't have to come off.
3. Using a 12mm ring spanner start undoing the front coupling nuts. They can be tough but will give. Once off push the spline into the shaft to dislodge it off the gearbox.
4. Now there's little room and you may have to rotate the shaft a little to get it in a position that will allow you to pull out the spline. But move it to the vehicles left side and you can slide it out past the transfer case. You may find it easier to disconnect the rear and drop the whole shaft for ease. Just chalk the alignment that end as well if you do.
5. I'm not sure if the spline realignment is critical but you can tell. On the inside of the drive shaft there is a missing channel ridge. This is seen on the spline where there has been no contact. Mark this point on the spline with a marker and use that to guide you when placing back into the shaft.
6. The spline surface will be coated very thinly with a heavy grey grease. I simply wipped it down and reapplied a heavy duty high temp bearing grease on it and some in the shaft
7. Reinstall the spline, wiping off excess. Reposition the boot. Line up the universal to gearbox coupling and bolt up. Use a large cable tie to resecure the boot and you should be done.
This was a one hour and two beers job. Hope that helps,
Wayne.
fairly straight forward. I firstly jacked up one rear wheel to allow me to rotate the drive shaft. You get to see how much slip you have in your LSD this way, but it will turn. Then under you go:
1. Mark with chalk the position of the front universal to the gearbox output coupling as a reference for reassembly.
2. Prise off only the rear facing ring clamp that holds the boot over the spline. The front one doesn't have to come off.
3. Using a 12mm ring spanner start undoing the front coupling nuts. They can be tough but will give. Once off push the spline into the shaft to dislodge it off the gearbox.
4. Now there's little room and you may have to rotate the shaft a little to get it in a position that will allow you to pull out the spline. But move it to the vehicles left side and you can slide it out past the transfer case. You may find it easier to disconnect the rear and drop the whole shaft for ease. Just chalk the alignment that end as well if you do.
5. I'm not sure if the spline realignment is critical but you can tell. On the inside of the drive shaft there is a missing channel ridge. This is seen on the spline where there has been no contact. Mark this point on the spline with a marker and use that to guide you when placing back into the shaft.
6. The spline surface will be coated very thinly with a heavy grey grease. I simply wipped it down and reapplied a heavy duty high temp bearing grease on it and some in the shaft
7. Reinstall the spline, wiping off excess. Reposition the boot. Line up the universal to gearbox coupling and bolt up. Use a large cable tie to resecure the boot and you should be done.
This was a one hour and two beers job. Hope that helps,
Wayne.
Wayne.
Greg,
this came out of all those forums above. No Frontera photos, but certain Fords in the US also suffer this known problem and these photos show fairly closely what to expect.
http://www.eurekaboy.com/f250/slipjoint.htm
Wayne.
this came out of all those forums above. No Frontera photos, but certain Fords in the US also suffer this known problem and these photos show fairly closely what to expect.
http://www.eurekaboy.com/f250/slipjoint.htm
Wayne.
Wayne.
Who is online
Users browsing this forum: No registered users and 12 guests