Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
options for zook build rebody vw baja
options for zook build rebody vw baja
hi all im building a vw baja convertible onto a ong wheel base zook i will be running 31 x 10 .5 and i belive if swap to a 1 liter transfer it bring my ratio's back so it will run better and not not be over geared because of the 31 inch tyres
and advice greatly appreciated
thanks rod
and advice greatly appreciated
thanks rod
1982 fj 60 with all late model gxl stuff 3 inches of lift ,snorkel ,lokker,bullbar,winch,ford 5 liter and a meggasquirt ECU
not quite, but youll be better off... however most choose to do tcase gears... gives you a perfect high range reduction and makes low range, well, actually low =) haha
Im running calmini 5.14 gears - 18% high range reduction and 180% low range. others run the 6.5 gears for even further reduction.
Im running calmini 5.14 gears - 18% high range reduction and 180% low range. others run the 6.5 gears for even further reduction.
The worst thing about censorship is ███████.
4x4 baja
yup 31's and a transfer case if i didnt want 4wd why on earth would i go to the hassel of putin it on a zook chassis
i dont want to go stupid off road as i have an over powered raised 60 seiries for that this is a toy that will be registered
i have got a shorty wheel base 1.3 5 speed zook
and a 1.0 4 speed rust bucket oops i mean zook
i will only use the bit i have if i can sell some bits i dont need to buy other bits i will but an extra low is not needed or wanted just want to make up the power loss from the 31,s by using the 1.0 transfer interested what the out come will be i will be be happy if its not quite as low as it was as i will prolly fit a g16a later and have a nice all round vehicle
have fun
rod
i dont want to go stupid off road as i have an over powered raised 60 seiries for that this is a toy that will be registered
i have got a shorty wheel base 1.3 5 speed zook
and a 1.0 4 speed rust bucket oops i mean zook
i will only use the bit i have if i can sell some bits i dont need to buy other bits i will but an extra low is not needed or wanted just want to make up the power loss from the 31,s by using the 1.0 transfer interested what the out come will be i will be be happy if its not quite as low as it was as i will prolly fit a g16a later and have a nice all round vehicle
have fun
rod
1982 fj 60 with all late model gxl stuff 3 inches of lift ,snorkel ,lokker,bullbar,winch,ford 5 liter and a meggasquirt ECU
baja zook
ok all did not know the diffs were a lower ratio.
The 1 liter is narrow track and the 1.3 wide track, are the centrers swapable or do you need to strip them and swap crownwheel and pinion .
i also have got my hands on (pick i tup this arvo) long wheel base ute chassis , i was hoping the body ounts were the same so i can fit the floor /trans tunel from the short wheel base on it and does anyone know the length of a rear tail shaft for the lwb
thanks rod
The 1 liter is narrow track and the 1.3 wide track, are the centrers swapable or do you need to strip them and swap crownwheel and pinion .
i also have got my hands on (pick i tup this arvo) long wheel base ute chassis , i was hoping the body ounts were the same so i can fit the floor /trans tunel from the short wheel base on it and does anyone know the length of a rear tail shaft for the lwb
thanks rod
1982 fj 60 with all late model gxl stuff 3 inches of lift ,snorkel ,lokker,bullbar,winch,ford 5 liter and a meggasquirt ECU
Who is online
Users browsing this forum: No registered users and 1 guest